Home › Suspension › REAR SUSPENSION › REAR STABILIZER BAR › 2017.09–2018.04
RM33A0E _53 Suspension _065362 REAR SUSPENSION _0319640 REAR STABILIZER BAR A

REAR SUSPENSION  REAR STABILIZER BAR  INSTALLATION  


PROCEDURE

Hide 48818 1.INSTALL REAR STABILIZER BUSHING

a.

Install the 2 rear stabilizer bushings to the rear stabilizer bar.

NOTICE:

Be sure to install the rear stabilizer bushings so that each cutout faces the front of the vehicle.



Hide 48832A 2.INSTALL REAR NO. 1 STABILIZER BAR BRACKET

a.
C370228C01
1.375,1.875 1.219,1.875 1.219,1.875 1.219,1.573 false 1.396,1.802 1.708,1.958 0.313,0.156 10 false *a
*a Arrow Mark
V100136

Front of the Vehicle


Install the 2 rear No. 1 stabilizer bar brackets to the 2 rear stabilizer bushings.

NOTICE:

Be sure to install the rear No. 1 stabilizer bar brackets so that each arrow mark faces the front of the vehicle.



Hide 48812 3.INSTALL REAR STABILIZER BAR

a.
C370225C01
0.542,1.344 0.542,1.042 true 0.469,1.354 0.677,1.552 0.208,0.198 10 true *a 0.906,0.542 1.115,0.708 0.208,0.167 10 true A 0.927,1.5 1.135,1.667 0.208,0.167 10 true B 2.479,1.448 2.688,1.615 0.208,0.167 10 true B 2.469,0.542 2.677,0.708 0.208,0.167 10 true A
*a Identification Mark


Install the rear stabilizer bar, 2 rear No. 1 stabilizer bar brackets and 2 rear stabilizer bushings to the rear suspension member sub-assembly with the 4 bolts.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

NOTICE:
·

Ensure that the identification mark faces the right side of the vehicle.

·

Temporarily tighten the bolt (A) and then fully tighten the 2 bolts in the order of (B) and (A).




Hide 48840A 5.INSTALL REAR STABILIZER LINK ASSEMBLY LH

a.
C376676N03
1.729,1.625 1.885,1.823 0.156,0.198 10 true A 0.958,4.167 1.115,4.365 0.156,0.198 10 true B

Install the rear stabilizer link assembly LH with the nut (A).

Torque:
75 N*m (765 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



b.

Install the rear stabilizer link assembly LH with the bolt and nut (B).

Torque:
75 N*m (765 kgf*cm, 55 ft.*lbf)


Hide 48830D 6.INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 58398F 8.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)

a.
C375073N01
1,0.115 1.156,0.313 0.156,0.198 10 true A 2.063,0.219 2.219,0.417 0.156,0.198 10 true B 1.979,0.854 2.135,1.052 0.156,0.198 10 true C 1.948,1.427 2.104,1.625 0.156,0.198 10 true C 0.458,0.479 0.615,0.677 0.156,0.198 10 true B

Install the No. 1 floor under cover with the 2 grommets (B) and 2 clips (C).


b.

Install the 2 bolts and clip (A).

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58399D 9.INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)

a.
C375074N01
2.354,0.083 2.51,0.281 0.156,0.198 10 true A 2.865,0.458 3.021,0.656 0.156,0.198 10 true B 1.313,0.771 1.469,0.969 0.156,0.198 10 true C 1.323,1.448 1.479,1.646 0.156,0.198 10 true C 1.281,0.125 1.438,0.323 0.156,0.198 10 true B

Install the No. 2 floor under cover with the 2 grommets (B) and 2 clips (C).


b.

Install the 2 bolts and clip (A).

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 10.INSTALL REAR WHEEL