The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
1.REMOVE REAR WHEEL
17420
2.REMOVE CENTER EXHAUST PIPE ASSEMBLY
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL
58399D
3.REMOVE NO. 2 FLOOR UNDER COVER (w/ Cover)
58398F
4.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)
47319F
5.SEPARATE REAR FLEXIBLE HOSE LH
Remove the bolt and separate the rear flexible hose LH from the rear flexible hose bracket.
47318F
6.SEPARATE REAR FLEXIBLE HOSE RH
Perform the same procedure as for the LH side.
89408C
7.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
48840A
8.REMOVE REAR STABILIZER LINK ASSEMBLY LH
48830D
9.REMOVE REAR STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
48812
10.REMOVE REAR STABILIZER BAR
48231B
11.REMOVE REAR COIL SPRING LH
48231A
12.REMOVE REAR COIL SPRING RH
Perform the same procedure as for the LH side.
48258C
13.REMOVE REAR LOWER COIL SPRING INSULATOR LH
48258B
14.REMOVE REAR LOWER COIL SPRING INSULATOR RH
Perform the same procedure as for the LH side.
48740F
15.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
48730F
16.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
17.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
18.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48790
19.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH
Remove the bolt and nut and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
48770A
20.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH
Use the same procedure as for the LH side.
51206A
21.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY
| *a | Engine Lifter |
| *b | Attachment |
|
Attachment Placement Location |
Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.
Remove the 2 bolts, 6 nuts, 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH.
Slowly lower the rear suspension member sub-assembly.
When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.
Remove the 4 rear suspension member cushions from the rear suspension member sub-assembly.
Make sure to place an identification mark on the rear suspension member cushion so that they can be reinstalled to their original positions.
48790
22.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH
48770A
23.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
52271D
24.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)
| *a | Bend Portion |
Using a chisel and hammer, bend the 2 portions of the rear suspension member front body mounting cushion rib.
Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.
Apply lubricant to the contact surfaces of the rear suspension member front body mounting cushion.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Using SST, remove the rear suspension member front body mounting cushion while applying lubricant into the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.
Set the claws of SST into the rear suspension member sub-assembly securely as shown in the illustration.
Tighten SST slowly and evenly.
Be careful as the rear suspension member front body mounting cushion may fly out.
The rear suspension member front body mounting cushion cannot be reused.
Remove SST and the rear suspension member front body mounting cushion from the rear suspension member sub-assembly.
52271D
25.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)
Perform the same procedure as for the LH side.
52276A
26.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Using SST, remove the rear suspension member rear body mount cushion LH while applying lubricant into the clearance between the rear suspension member rear body mount cushion LH and the rear suspension member sub-assembly.
Tighten SST slowly and evenly.
Be careful as the rear suspension member rear body mount cushion LH may fly out.
The rear suspension member rear body mount cushion LH cannot be reused.
Remove SST and the rear suspension member rear body mount cushion LH from the rear suspension member sub-assembly.
52275B
27.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH
Perform the same procedure as for the LH side.