Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320457 WIPER AND WASHER SYSTEM Y

WIPER / WASHER  WIPER AND WASHER SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the wiper and washer system.


·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.READ OUT AND SAVE OPERATION HISTORY
3.READ OUT AND SAVE OPERATION HISTORY
NOTICE:
·

If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.

·

The function "Read operation history" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the GTS system clock is accurately set to the current time.



a.

Read out and save operation history using the GTS.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Body Electrical > Wiper > Utility
Tester Display
Operation History
50005 384 1052

Result:
Proceed to
NEXT



NEXT

4.PRE-CHECK
4.PRE-CHECK
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Check for DTCs.

Body Electrical > Wiper > Trouble Codes
50001 384
Body Electrical > Main Body > Trouble Codes
50001 123
Body Electrical > Rain and/or Humidity Sensor > Trouble Codes
50001 199

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.PROBLEM SYMPTOMS TABLE

B

7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END