Under normal operation, the windshield wiper motor assembly receives operation signals from the windshield wiper switch assembly via LIN communication.
The windshield wiper motor assembly and windshield wiper switch assembly are also connected via direct line in order to operate the front wipers in HI in an emergency. If the operation signals sent via LIN communication and direct line do not match, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from |
|---|---|---|---|---|---|
| B1372 | Wiper Switch Signal Mismatch between LIN and Line | Detection condition:
Battery voltage is 9.5 V or more Malfunction Status:
The operation signals sent via LIN communication and direct line do not match Malfunction Time:
10 seconds or more |
·
Windshield wiper motor assembly ·
Main body ECU (multiplex network body ECU) ·
Steering sensor ·
Harness or connector |
○ | Wiper |
for LHD
for RHD
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2
*1: w/ Door Control Battery
*2: w/ Smart Entry and Start System
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Wiper / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Wiper / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1372 is not output | A |
| DTC B1372 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Wiper / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper Switch HI (Line) | Front wiper switch HI position signal (direct line) | OFF or ON | OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position |
- |
| Tester Display |
|---|
| Wiper Switch HI (Line) |
The GTS display is normal.
| Result |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Steering Angle Sensor / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper Hi Switch | Front wiper switch HI position signal | OFF or ON | OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position |
- |
| Tester Display |
|---|
| Wiper Hi Switch |
The GTS display is normal.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the K51 main body ECU (multiplex network body ECU) connector.
Disconnect the A31 windshield wiper motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (LIN3) - A31-2 (LIN) | Always | Below 1 Ω |
| K51-3 (LIN3) or A31-2 (LIN) - Body ground | Always | 10 kΩ Higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (LIN3) - A31-3 (LIN) | Always | Below 1 Ω |
| K51-3 (LIN3) or A31-3 (LIN) - Body ground | Always | 10 kΩ Higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) |
Check for voltage and pulses according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K51-3 (LIN3) - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K71 steering sensor connector.
Disconnect the A31 windshield wiper motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K71-2 (2S) - A31-3 (2S) | Always | Below 1 Ω |
| K71-2 (2S) or A31-3 (2S) - Body ground | Always | 10 kΩ Higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K71-2 (2S) - A31-2 (2S) | Always | Below 1 Ω |
| K71-2 (2S) or A31-2 (2S) - Body ground | Always | 10 kΩ Higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Steering Sensor) |
- | - |
Remove the steering sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K71-2 (2S) - z6-27 (+2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG