Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU › 2017.09–2018.04
RM33A0E _57 Power Source / Network _065376 POWER DISTRIBUTION _0326910 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Main body ECU (multiplex network body ECU)*1 Perform code registration (Engine immobiliser system)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for LHD)

Hide 3. DISCHARGE DOOR CONTROL BATTERY AND DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Door Control Battery)

NOTICE:
·

Always ensure that the cable is disconnected from the negative (-) battery terminal and the door control battery is fully discharged when removing or installing the junction block assembly.

·

Make sure to perform the following procedure before removal and installation of the junction block assembly.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:
·

When the engine switch is turned off after the door control battery is fully charged, the door control battery becomes completely discharged due to self-discharge within approximately 30 minutes.

·

Approximately 90 seconds after the engine switch is turned on (IG), the door control battery becomes fully charged.

·

When approximately 30 minutes or more have elapsed after the engine switch is turned off, the Active Test may not be able to be performed.



a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.

Body Electrical > Main Body > Active Test
Tester Display Control Range
Shock Detection Unlock ON/OFF
NOTICE:

Do not perform the Active Test at this time.



e.

Disconnect the cable from the negative (-) battery terminal.


f.

Perform the "Shock Detection Unlock" Active Test repeatedly until the multiplex network body ECU (main body ECU) communication lost error message "Lost communication with vehicle" is displayed on the GTS.

Body Electrical > Main Body > Active Test
Tester Display
Shock Detection Unlock
50004 123 21
HINT:
·

When the cable is disconnected from the negative (-) battery terminal and the door control battery becomes completely discharged, the multiplex network body ECU (main body ECU) communication lost message "Lost communication with vehicle" is displayed on the GTS.

·

The number of times the Active Test can be performed depends on the charge condition of the door control battery.




Hide 73900 4.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

Hide 55308B 5.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD)

Hide 67914 6.REMOVE FRONT DOOR SCUFF PLATE LH (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62112A 7.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62312B 8.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55318C 9.REMOVE INSTRUMENT SIDE PANEL LH (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55607 10.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 55435B 11.REMOVE NO. 1 METER HOOD CLUSTER (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 55012A 12.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 55476C 13.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


Hide 55303B 14.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure for RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 15.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

a.

for LHD:

i.
E336665

Disconnect each connector.


ii.

Disengage the clamp.


iii.
E336666C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration.


iv.
E336668

Disconnect each connector.


v.
E336669

Remove the 2 nuts.


vi.
E336674C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw and guide and pull out the instrument panel junction block assembly with main body ECU.


vii.
E336671

Disengage the clamp.


viii.
E336670

Disengage the clamp.


ix.
E336672C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration and remove the instrument panel junction block assembly with main body ECU.



b.

for RHD:

i.
E373976

Disconnect each connector.


ii.
E373977C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration.


iii.
E373979

Remove the 2 nuts.


iv.
E373980

Disengage the clamp.


v.
E365269C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw and guide and pull out the instrument panel junction block assembly with main body ECU.


vi.
E365271

Disengage the clamp.


vii.
E373981

Disengage the clamp.


viii.
E373982C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration and remove the instrument panel junction block assembly with main body ECU.



Hide 82715 16.REMOVE WIRING HARNESS CLAMP BRACKET

a.
E336676

Remove the nut.


b.

Disengage the guide to remove the wiring harness clamp bracket.


Hide 17.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E336677C01
0.708,2.833 1.208,2.833 true 0.188,2.792 0.521,2.792 true 1.229,2.719 1.542,2.875 0.313,0.156 10 false *1 0.042,2.688 0.354,2.844 0.313,0.156 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100135

Push in this Direction


Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.


b.
E336678C01
1.698,1.958 1.833,1.708 false 1.604,1.958 1.917,2.156 0.313,0.198 10 false *a
*a Protective Tape
V100135

Insert in this Direction
V113147

Remove in this Direction


With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and junction block assembly.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).




c.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



d.
E336679C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.

NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.