Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320457 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B1245  Lost Communication with Wiper ECU LIN  


DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield wiper motor assembly communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from
B1245 Lost Communication with Wiper ECU LIN
Detection condition:

Battery voltage is 9.5 V or more


Malfunction Status:

A communication malfunction between the main body ECU (multiplex network body ECU) and windshield wiper motor assembly


Malfunction Time:

10 seconds or more


·

Windshield wiper motor assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector


○ Main Body

WIRING DIAGRAM

E378083E01
2.354,0.479 3.729,0.677 1.375,0.198 10 false From WIPER Relay 2.323,1.26 3.698,1.458 1.375,0.198 10 false LIN3 2.708,1.104 4.083,1.302 1.375,0.198 10 false 3 0.115,1.719 1.49,1.917 1.375,0.198 10 false K51 0.115,1.875 3.365,2.104 3.25,0.229 10 false Main Body ECU (Multiplex Network Body ECU) 0.948,3.365 2.99,3.625 2.042,0.26 10 false : LIN Communication Line 2.844,2.802 4.219,3 1.375,0.198 10 false *1: for LHD 2.844,3.125 4.219,3.323 1.375,0.198 10 false *2: for RHD 5.427,2.875 6.917,3.396 1.49,0.521 10 false Windshield Wiper Motor Assembly 5.427,2.708 6.802,2.906 1.375,0.198 10 false A31 5.542,0.5 6.917,0.698 1.375,0.198 10 false +B 5.542,1.25 6.917,1.448 1.375,0.198 10 false LIN 5.542,1.833 6.917,2.031 1.375,0.198 10 false GND 4.917,0.396 6.292,0.594 1.375,0.198 10 false 4*1, 1*2 4.927,1.094 6.302,1.292 1.375,0.198 10 false 2*1, 3*2 4.927,1.719 6.302,1.917 1.375,0.198 10 false 1*1, 4*2

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


e.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only DTC B1245 is output A
DTC B1245 and B1373 are output B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the A31 windshield wiper motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K51-3 (LIN3) - A31-2 (LIN) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
K51-3 (LIN3) - A31-3 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
E366392C01
1.5,0.25 1.917,0.5 0.417,0.25 0.76,1.646 1.167,0.917 false 1.594,0.292 2,0.531 0.406,0.24 10 false K51 0.604,1.719 0.938,1.917 0.333,0.198 10 false LIN3 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Main Body ECU (Multiplex Network Body ECU)


a.

Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K51-3 (LIN3) - Body ground Ignition switch off Below 1 V
Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A31-4 (+B) - Body ground Ignition switch ON 11 to 14 V
Less than approximately 60 seconds after ignition switch turned off 11 to 14 V
Approximately 60 seconds after ignition switch turned off Below 1 V

for RHD
Tester Connection Condition Specified Condition
A31-1 (+B) - Body ground Ignition switch ON 11 to 14 V
Less than approximately 60 seconds after ignition switch turned off 11 to 14 V
Approximately 60 seconds after ignition switch turned off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A31-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A31-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR