Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › CYLINDER HEAD › 2017.09–2018.04
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321409 CYLINDER HEAD A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

*3: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft

(for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel injector assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly Perform the following procedures in the order shown:
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


(Click here)for U760E Initialization
(Click here)for U760E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)
Suspension, tires*3 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 13715 1.REMOVE EXHAUST VALVE

a.
A337755N02
2.385,0.479 2.5,0.167 2.5,0.167 2.583,0.167 false 0.729,0.292 0.75,1.833 0.75,1.833 0.833,1.833 true 2.615,0.083 3.073,0.281 0.458,0.198 10 false SST 0.854,1.75 1.313,1.948 0.458,0.198 10 false SST

Using SST, compress the compression spring and remove the valve spring retainer lock.

SST
09202-00021  
09202-70020  (09202-01010, 09202-01020)


b.

Remove the valve spring retainer, compression spring and exhaust valve from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13711 2.REMOVE INTAKE VALVE

a.
A337754N02
0.417,0.167 0.583,0.167 0.583,0.167 1.052,0.521 true 2.25,0.167 2.333,0.167 2.333,0.167 2.604,0.229 true 0.104,0.094 0.563,0.292 0.458,0.198 10 false SST 1.958,0.094 2.417,0.292 0.458,0.198 10 false SST

Using SST, compress the compression spring and remove the valve spring retainer lock.

SST
09202-00021  
09202-70020  (09202-01010, 09202-01020)


b.

Remove the valve spring retainer, compression spring and intake valve from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13711E 3.REMOVE VALVE STEM OIL SEAL

a.
A194958

Using needle-nose pliers, remove the 8 intake valve stem oil seals and 8 exhaust valve stem oil seals.


Hide 13734 4.REMOVE VALVE SPRING SEAT

a.
A194959

Using compressed air and a Magnet Hand, remove the 16 valve spring seats by blowing air onto them.


Hide 11117E 5.REMOVE NO. 1 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.


a.
A194960

Using a 10 mm hexagon wrench, remove the 3 No. 1 straight screw plugs and 3 gaskets.


Hide 11117F 6.REMOVE NO. 2 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from the No. 2 straight screw plug or a plug is corroded, replace it.


a.
A194961

Using a 14 mm hexagon wrench, remove the No. 2 straight screw plug and gasket.


Hide 17159 7.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A242246

Using an E7 or E8 "TORX" socket wrench, remove the 5 stud bolts.