Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK › 2017.09–2018.04
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321410 CYLINDER BLOCK A

2AR-FE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

*3: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft

(for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel injector assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of knock control sensor

·

Replacement of engine coolant temperature sensor

·

Replacement of piston or piston ring


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly Perform the following procedures in the order shown:
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


(Click here)for U760E Initialization
(Click here)for U760E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)
Suspension, tires*3 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A259168

Using a dial indicator, measure the thrust clearance while moving the connecting rod sub-assembly back and forth.

Standard Thrust Clearance:

0.160 to 0.512 mm (0.00630 to 0.0202 in.)


Maximum Thrust Clearance:

0.512 mm (0.0202 in.)


HINT:

If the thrust clearance is more than the maximum, replace the connecting rod sub-assembly. If necessary, replace the crankshaft.



Hide 2.INSPECT CONNECTING ROD OIL CLEARANCE

a.
A338770C03
0.688,0.854 1.365,0.469 1.365,0.469 1.521,0.469 true 1.552,0.385 1.865,0.583 0.313,0.198 10 false *a
*a Alignment Mark


Check the alignment marks on the connecting rod and connecting rod cap so that they can be reinstalled to their original locations.


b.
A259170

Remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



c.

Clean the crank pin and connecting rod bearing.


d.

Check the crank pin and connecting rod bearing for pitting and scratches.

HINT:

If the crank pin or connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, replace the crankshaft.



e.
A259171C07
1.479,1.146 0.698,0.885 0.698,0.885 0.604,0.885 true 0.406,0.792 0.573,0.969 0.167,0.177 10 false *a
*a Plastigage


Lay a strip of Plastigage on the crank pin.


f.
A259172C11
1.438,0.885 0.729,0.625 0.729,0.625 0.604,0.625 true 0.396,0.542 0.604,0.719 0.208,0.177 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing the correct direction, and install the connecting rod cap.


g.
A259170

Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.


h.

Install and alternately tighten the 2 connecting rod bolts in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


i.
A101478C42
2.063,0.76 2.333,0.177 2.333,0.177 2.479,0.177 false 1.146,0.385 1.469,0.594 0.323,0.208 10 false 90° 2.49,0.083 2.698,0.281 0.208,0.198 10 false *a
*a Paint Mark
V100136

Front of Engine


Mark the front of each connecting rod bolt with paint.


j.

Tighten the connecting rod bolts 90° as shown in the illustration.

NOTICE:

Do not turn the crankshaft during the measurement.



k.

Remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



l.
A259173C09
1.146,0.948 1,0.458 1,0.458 0.917,0.458 true 1.479,3.188 0.719,3.667 0.719,3.667 1.229,4.177 true 1.479,3.469 0.719,3.667 true 0.729,0.365 0.938,0.594 0.208,0.229 10 false *a 0.51,3.573 0.719,3.802 0.208,0.229 10 false *b
*a Plastigage
*b Number Mark


Measure the Plastigage at its widest point.

Standard Oil Clearance:

0.033 to 0.063 mm (0.00130 to 0.00248 in.)


Maximum Oil Clearance:

0.07 mm (0.00276 in.)


NOTICE:

Remove the Plastigage completely after the measurement.


HINT:
·

If replacing a connecting rod bearing, select a new one with the same number as marked on the connecting rod cap. There are 3 sizes of standard connecting rod bearings, marked "1", "2" or "3" accordingly.

·

If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, replace the crankshaft.



Standard Crank Pin Diameter:

51.492 to 51.500 mm (2.02724 to 2.02756 in.)


Standard Connecting Rod Big End Inside Diameter:
Mark Specified Condition
1 54.500 to 54.508 mm (2.14567 to 2.14598 in.)
2 54.509 to 54.516 mm (2.14602 to 2.14629 in.)
3 54.517 to 54.524 mm (2.14633 to 2.14661 in.)


Standard Connecting Rod Bearing Center Wall Thickness:
Mark Specified Condition
1 1.486 to 1.490 mm (0.0585 to 0.0587 in.)
2 1.491 to 1.494 mm (0.0587 to 0.0588 in.)
3 1.495 to 1.498 mm (0.0589 to 0.0590 in.)



m.

Perform the inspection above for each cylinder.


Hide 3.REMOVE PISTON WITH CONNECTING ROD

a.
A194883C02
1.208,0.906 2.208,0.625 2.208,0.625 2.406,0.625 false 2.49,0.531 2.802,0.729 0.313,0.198 10 false *a
*a Ridge Reamer


Using a ridge reamer, remove all the carbon from the top of each cylinder.


b.

Remove the 8 connecting rod bolts, 4 connecting rod caps and 4 connecting rod bearings.


c.

Push the piston with connecting rod sub-assembly and connecting rod bearing out through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearings, connecting rod sub-assembly and connecting rod cap together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings from the connecting rod sub-assembly and connecting rod cap.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 5.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A259174

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard Thrust Clearance:

0.04 to 0.24 mm (0.00157 to 0.00945 in.)


Maximum Thrust Clearance:

0.30 mm (0.0118 in.)


HINT:

If the thrust clearance is more than the maximum, replace the crankshaft thrust washers as a set. If necessary, replace the crankshaft.


Standard Thrust Washer Thickness:

1.93 to 1.98 mm (0.0760 to 0.0780 in.)



Hide 13411 6.REMOVE CRANKSHAFT

a.
A285363N11
3.094,1.552 3.25,1.75 0.156,0.198 10 false 1 3.125,0.573 3.281,0.771 0.156,0.198 10 false 2 2.469,0.5 2.625,0.698 0.156,0.198 10 false 6 1.708,0.448 2.031,0.604 0.323,0.156 10 false 10 1.021,0.49 1.177,0.688 0.156,0.198 10 false 8 0.427,0.552 0.583,0.75 0.156,0.198 10 false 4 0.427,1.563 0.583,1.76 0.156,0.198 10 false 3 1.052,1.615 1.208,1.813 0.156,0.198 10 false 7 1.76,1.646 1.917,1.844 0.156,0.198 10 false 9 2.469,1.615 2.625,1.813 0.156,0.198 10 false 5

Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several steps in the order shown in the illustration.


b.

Remove the 5 crankshaft bearing caps from the cylinder block sub-assembly.

HINT:
·

Keep the No. 2 crankshaft bearings and crankshaft bearing caps together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




c.

Remove the crankshaft from the cylinder block sub-assembly.

HINT:

Keep the crankshaft bearings and crankshaft thrust washers together with the cylinder block sub-assembly.



d.

Check each crankshaft journal and crankshaft bearing for pitting and scratches.

HINT:

If the journal or crankshaft bearing is damaged, replace the crankshaft bearings. If necessary, replace the crankshaft.



Hide 11791 7.REMOVE CRANKSHAFT THRUST WASHER

a.
A195787

Remove the crankshaft thrust washers from the cylinder block sub-assembly.


Hide 11711 8.REMOVE CRANKSHAFT BEARING

a.

Remove the crankshaft bearings and No. 2 crankshaft bearings from the cylinder block sub-assembly and crankshaft bearing caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13471A 9.REMOVE CRANKSHAFT PULLEY KEY

a.

Using a screwdriver, remove the 2 crankshaft pulley keys from the crankshaft.


Hide 13011 10.REMOVE PISTON RING SET

a.
A194884C13
1.052,1.75 1.052,1.646 false 1.052,1.646 1.281,1.313 false 0.979,1.75 1.156,1.906 0.177,0.156 10 false *a
*a Piston Ring Expander


Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the oil ring expander, upper side rail and lower side rail by hand.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13101A 11.REMOVE PISTON PIN HOLE SNAP RING

a.
A194885C13
1.448,0.99 1.177,0.25 1.177,0.25 1.094,0.25 true 1.635,1.094 1.083,1.563 1.083,1.563 0.917,1.563 true 0.906,0.156 1.333,0.417 0.427,0.26 10 false *b 0.719,1.469 1.052,1.833 0.333,0.365 10 false *a
*a Front Mark Cutout Portion
*b Protective Tape


Using a screwdriver, pry out the piston pin hole snap ring (front side).

NOTICE:
·

Do not remove the piston pin hole snap ring (rear side) unless it has to be replaced.

·

Be careful not to damage the piston when removing the piston pin hole snap ring (rear side).



HINT:

Tape the screwdriver tip before use.



Hide 13211 12.REMOVE PISTON

a.
A194886

Gradually heat each piston to between 80 and 90°C (176 to 194°F).


b.
A194887

Using a brass bar and a hammer, lightly tap out the piston pin. Then remove the connecting rod sub-assembly.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 15708 13.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A195788

Using a 5 mm hexagon wrench, remove the 2 bolts and 2 No. 1 oil nozzle sub-assemblies.


Hide 15709 14.REMOVE NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.
A195789

Using a 5 mm hexagon wrench, remove the 4 bolts and 4 No. 2 oil nozzle sub-assemblies.


Hide 15.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A259692

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.