Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter CAN reception error
·

Local bus communication line

·

Combination meter assembly power source circuit

·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E367320E03
2.448,1.75 4.292,1.948 1.844,0.198 10 false Combination Meter Assembly 3.583,0.781 4.198,0.979 0.615,0.198 10 false TX- 3.573,0.333 4.188,0.531 0.615,0.198 10 false TX+ 2.448,1.604 3.063,1.802 0.615,0.198 10 false K21 3.875,0.229 4.5,0.385 0.625,0.156 10 false 36 3.875,1.104 4.51,1.25 0.635,0.146 10 false 21 5.635,0.229 6.26,0.385 0.625,0.156 10 false 5 5.625,0.646 6.25,0.802 0.625,0.156 10 false 6 5.427,1.552 6.042,1.75 0.615,0.198 10 false K2 5.427,1.708 7.115,2.042 1.688,0.333 10 false Radio and Display Receiver Assembly 5.792,0.365 6.406,0.563 0.615,0.198 10 false CNH1 5.802,0.802 6.417,1 0.615,0.198 10 false CNL1 0.896,2.219 5.479,2.417 4.583,0.198 10 false : Local Bus Communication Line 3.594,1.219 3.906,1.417 0.313,0.198 10 false ES 3.875,0.656 4.51,0.802 0.635,0.146 10 false 37 2.771,0.354 3.083,0.552 0.313,0.198 10 false B 2.771,0.771 3.083,0.969 0.313,0.198 10 false IG+ 2.552,0.677 3.188,0.823 0.635,0.146 10 false 39 2.552,0.25 3.188,0.396 0.635,0.146 10 false 40 0.271,0.76 1.656,1.021 1.385,0.26 10 false from IG2-NO. 2 Relay 0.802,0.344 2.396,0.708 1.594,0.365 10 false from Battery 1.885,0.917 2.969,1.302 1.083,0.385 10 false METER-IG2 1.677,0.469 2.76,0.854 1.083,0.385 10 false ECU-DCC NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.


·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)
a.

Disconnect the K21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-21 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-40 (B) - Body ground Always 11 to 14 V
K21-39 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-36 (TX+) - K21-37 (TX-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-5 (CNH1) - K21-36 (TX+) Always Below 1 Ω
K2-6 (CNL1) - K21-37 (TX-) Always Below 1 Ω
K2-5 (CNH1) or K21-36 (TX+) - Body ground Always 10 kΩ or higher
K2-6 (CNL1) or K21-37 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR