Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15DA  Rear Console Recognition Disconnected  


DESCRIPTION

The cooler control switch assembly is connected via AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and cooler control switch assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15DA Rear Console Recognition Disconnected When either of the following conditions is met:
·

The cooler control switch assembly is/was not connected while the ignition switch is/was ACC or IG

·

Communication between the master unit and the cooler control switch assembly is not possible when the engine is started.


·

Cooler control switch assembly power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and cooler control switch assembly

·

Cooler control switch assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E372494E04
5.563,4.083 6.885,4.625 1.323,0.542 10 false Cooler Control Switch Assembly 5.354,3.969 5.771,4.292 0.417,0.323 10 false Z1 3.125,3.219 4.823,3.844 1.698,0.625 10 false Radio and Display Receiver Assembly 5.406,2.198 5.823,2.521 0.417,0.323 10 false 7 5.406,2.583 5.823,2.906 0.417,0.323 10 false 8 5.615,2.323 6.031,2.646 0.417,0.323 10 false TX+ 5.625,2.729 6.042,3.052 0.417,0.323 10 false TX- 5.594,0.542 6.01,0.865 0.417,0.323 10 false +B 5.594,0.99 6.01,1.313 0.417,0.323 10 false ACC 5.604,1.479 6.021,1.802 0.417,0.323 10 false IG+ 5.417,0.427 5.833,0.75 0.417,0.323 10 false 9 5.427,0.885 5.844,1.208 0.417,0.323 10 false 1 5.375,1.365 5.792,1.688 0.417,0.323 10 false 10 3.052,3.031 3.49,3.427 0.438,0.396 10 false K3 4.323,2.177 4.76,2.573 0.438,0.396 10 false 5 4.323,2.573 4.76,2.969 0.438,0.396 10 false 6 3.938,2.313 4.354,2.635 0.417,0.323 10 false TX1+ 3.958,2.688 4.375,3.01 0.417,0.323 10 false TX1- 5.604,3.521 6.021,3.844 0.417,0.323 10 false GND 5.375,3.406 5.792,3.729 0.417,0.323 10 false 16 1.01,4.333 3.479,4.646 2.469,0.313 10 false : AVC-LAN Communication Line 3.365,0.667 4.458,1.021 1.094,0.354 10 false ECU-B NO. 2 3.438,1.156 4.531,1.51 1.094,0.354 10 false ECU-ACC 3.281,1.625 4.375,1.979 1.094,0.354 10 false ECU-IG1 NO. 4 0.99,0.979 2.479,1.385 1.49,0.406 10 false from ACC Relay 0.708,1.438 2.198,1.844 1.49,0.406 10 false from IG1 NO. 1 Relay 1.219,0.51 2.219,0.917 1,0.406 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.



·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY POWER SOURCE)
a.

Disconnect the Z1 cooler control switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-16 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Z1-9 (+B) - Z1-16 (GND) Always 11 to 14 V
Z1-10 (IG+) - Z1-16 (GND) Ignition switch ON 11 to 14 V
Z1-1 (ACC) - Z1-16 (GND) Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the Z1 cooler control switch assembly connector.


b.

Disconnect the K3 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-7 (TX+) - K3-5 (TX1+) Always Below 1 Ω
Z1-8 (TX-) - K3-6 (TX1-) Always Below 1 Ω
Z1-7 (TX+) or K3-5 (TX1+) - Body ground Always 10 kΩ or higher
Z1-8 (TX-) or K3-6 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE COOLER CONTROL SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE COOLER CONTROL SWITCH ASSEMBLY
a.

Replace the cooler control switch assembly with a new or known good one.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>DISASSEMBLY


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY