Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM33A0E _57 Power Source / Network _065377 NETWORKING _0323332 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1206  P/W Master Switch Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1206 P/W Master Switch Communication Stop No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Multiplex network master switch assembly

·

Wire harness or connector

·

ECU-B NO. 2 fuse



WIRING DIAGRAM

B484503E08
4.75,3.365 5.885,3.802 1.135,0.438 10 false *1: for LHD 5.531,0.479 6.479,0.896 0.948,0.417 10 false ECU-B NO. 2 6,1.146 6.313,1.344 0.313,0.198 10 false 11 5.792,1.25 5.969,1.458 0.177,0.208 10 false B 5.604,1.958 6.063,2.156 0.458,0.198 10 false GND 5.042,1.271 5.656,1.469 0.615,0.198 10 false LIN1 4.771,1.104 5.083,1.302 0.313,0.198 10 false 17 3.427,1.104 3.74,1.302 0.313,0.198 10 false 25 2.396,1.104 2.708,1.302 0.313,0.198 10 false 16 2,1.26 2.615,1.458 0.615,0.198 10 false LIN2 0.833,3.354 4.5,3.552 3.667,0.198 10 false : LIN Communication Line 0.875,2.313 1.188,2.51 0.313,0.198 10 false MB 0.875,2.458 2.521,3.104 1.646,0.646 10 false Main Body ECU (Multiplex Network Body ECU) 2.635,1.823 2.948,2.021 0.313,0.198 10 false 3D 2.656,1.969 4.281,2.615 1.625,0.646 10 false Instrument Panel Junction Block Assembly 4.781,2.323 5.625,2.604 0.844,0.281 10 false O2*1, N2*2 4.781,2.49 6.375,3.115 1.594,0.625 10 false Multiplex Network Master Switch Assembly 6.01,1.844 6.323,2.042 0.313,0.198 10 false 12 4.615,0.323 5.667,0.729 1.052,0.406 10 false from Battery 5.833,3.365 6.969,3.802 1.135,0.438 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B426689C20
2,1 2.417,1.25 0.417,0.25 5.5,0.75 5.917,1 0.417,0.25 2.198,2.156 2.198,1.573 false 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.115,1.042 2.427,1.24 0.313,0.198 10 false MB 5.615,0.792 5.927,0.99 0.313,0.198 10 false 3D 2.083,2.219 2.698,2.417 0.615,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3D-25 - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the O2*1 or N2*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3D-25 - O2-17 (LIN1) Ignition switch off Below 1 Ω
3D-25 or O2-17 (LIN1) - Body ground Ignition switch off 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
3D-25 - N2-17 (LIN1) Ignition switch off Below 1 Ω
3D-25 or N2-17 (LIN1) - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
O2-11 (B) - O2-12 (GND) Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
N2-11 (B) - N2-12 (GND) Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
O2-12 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
N2-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Replace the multiplex network master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1206 is not output.



Result:
Proceed to
OK
NG



OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)