Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM33A0E _57 Power Source / Network _065377 NETWORKING _0323332 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (driver door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2321 Driver Side Door ECU Communication Stop No communication between power window regulator motor assembly (driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Multiplex network master switch assembly

·

Power window regulator motor assembly (driver door)

·

Wire harness or connector

·

DOOR F/L fuse*1

·

DOOR F/R fuse*2



*1: for LHD

*2: for RHD


WIRING DIAGRAM

B486910E06
0.688,3.354 2.375,3.802 1.688,0.448 10 false : LIN Communication Line 0.073,2.063 0.583,2.323 0.51,0.26 10 false MB 0.073,2.219 1.208,2.917 1.135,0.698 10 false Main Body ECU (Multiplex Network Body ECU) 1.479,1.667 1.99,1.927 0.51,0.26 10 false 3D 1.49,1.823 3.104,2.208 1.615,0.385 10 false Instrument Panel Junction Block Assembly 1.042,1.021 1.552,1.281 0.51,0.26 10 false LIN2 3.594,1.01 4.104,1.271 0.51,0.26 10 false LIN1 1.406,0.875 1.917,1.135 0.51,0.26 10 false 16 2.323,0.885 2.833,1.146 0.51,0.26 10 false 25 3.333,0.885 3.844,1.146 0.51,0.26 10 false 17 5.604,0.885 6.115,1.146 0.51,0.26 10 false 9 6.115,0.292 7,0.625 0.885,0.333 10 false DOOR F/L*1, DOOR F/R*2 4.979,0.135 5.927,0.375 0.948,0.24 10 false from Battery 6.521,0.823 7.031,1.083 0.51,0.26 10 false B 6.333,1.698 6.844,1.958 0.51,0.26 10 false GND 5.125,2.094 6.031,2.323 0.906,0.229 10 false O6*1, N7*2 5.135,2.271 7.083,2.854 1.948,0.583 10 false Power Window Regulator Motor Assembly (Driver Door) 3.333,1.625 4.24,1.938 0.906,0.313 10 false O2*1, N2*2 3.333,1.792 4.917,2.313 1.583,0.521 10 false Multiplex Network Master Switch Assembly 4.167,1.01 4.677,1.271 0.51,0.26 10 false LIN2 5.771,1.031 6.281,1.292 0.51,0.26 10 false LIN 4.542,0.885 5.052,1.146 0.51,0.26 10 false 16 6.698,1.583 7.104,1.844 0.406,0.26 10 false 1 6.708,0.74 7.115,1 0.406,0.26 10 false 2 5.135,3.354 6.031,3.802 0.896,0.448 10 false *1: for LHD 6.063,3.354 6.958,3.802 0.896,0.448 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.
B365181C11
0.24,0.135 0.552,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Multiplex Network Master Switch Assembly)


Remove the multiplex network master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 - 17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B426689C20
2,1 2.417,1.25 0.417,0.25 5.5,0.75 5.917,1 0.417,0.25 2.198,2.156 2.198,1.573 false 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.115,1.042 2.427,1.24 0.313,0.198 10 false MB 5.615,0.792 5.927,0.99 0.313,0.198 10 false 3D 2.083,2.219 2.698,2.417 0.615,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3D-25 - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3D-25 - O2-17 (LIN1) Ignition switch off Below 1 Ω
3D-25 or O2-17 (LIN1) - Body ground Ignition switch off 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
3D-25 - N2-17 (LIN1) Ignition switch off Below 1 Ω
3D-25 or N2-17 (LIN1) - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
a.

Disconnect the O6*1 or N7*2 power window regulator motor assembly (driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
O2-16 (LIN2) - O6-9 (LIN) Ignition switch off Below 1 Ω
O2-16 (LIN2) or O6-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
N2-16 (LIN2) - N7-9 (LIN) Ignition switch off Below 1 Ω
N2-16 (LIN2) or N7-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
O6-2 (B) - O6-1 (GND) Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
N7-2 (B) - N7-1 (GND) Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
O6-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
N7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)
a.

Replace the power window regulator motor assembly (driver door).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Front Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B2321 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)