This DTC is stored when LIN communication between the roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2329 | Lost Communication with Sliding Sunshade ECU | No communication between roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Roof sunshade ECU (sliding roof drive gear assembly) ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Wire harness or connector ·
S/ROOF fuse |
Inspect the fuses for circuits related to this system before performing the following procedure.
When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*
*: w/ Smart Entry and Start System
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: w/ Door Control Battery
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-17 - MB-16 (LIN2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the q2 roof sunshade ECU (sliding roof drive gear assembly) connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-17 - q2-7 (LIN) | Ignition switch off | Below 1 Ω |
| 3B-17 or q2-7 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| q2-1 (+B) - q2-2 (E) | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| q2-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the roof sunshade ECU (sliding roof drive gear assembly).
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2329 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG