Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL › 2017.09–2021.02
RM33A0E _52 Drivetrain _065352 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0326592 DIFFERENTIAL OIL SEAL A

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 43457 2.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 43420H 3.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C370847N01
1.083,2.552 1.229,2.552 1.229,2.552 1.396,1.896 false 0.76,2.448 1.104,2.646 0.344,0.198 10 false SST

Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the automatic transaxle case sub-assembly.



Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C370848N01
2.5,3.052 2.323,3.052 2.323,3.052 1.979,1.927 false 2.552,2.927 2.917,3.146 0.365,0.219 10 false SST

Using SST, remove the front drive shaft oil seal RH from the transaxle housing.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle housing.



Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C370849C01
1.604,1.125 2.75,1 2.75,1 2.344,1.698 true 1.469,2.646 1.813,2.906 0.344,0.26 10 false *a 2.813,0.906 3.198,1.177 0.385,0.271 10 false SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal RH is installed in the correct direction.

·

Do not damage the lip of the front drive shaft oil seal RH.




Hide 43420H 6.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C370850C01
0.875,1.344 2.875,1.615 2.875,1.615 1.885,1.188 true 2.104,2.729 2.417,2.969 0.313,0.24 10 false *a 2.927,1.521 3.26,1.75 0.333,0.229 10 true SST
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly.

SST
09649-17010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal LH is installed in the correct direction.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 43457 7.INSTALL DRIVE SHAFT BEARING BRACKET