Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065342 A25A-FKS ENGINE MECHANICAL _0319522 ENGINE UNIT A

A25A-FKS ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for UB80E Initialization
(Click here)for UB80E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 43457 1.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A400916

Remove the 3 bolts and drive shaft bearing bracket.


Hide 16361A 2.REMOVE V-RIBBED BELT

Hide 88310 4.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

a.

for Type A:

i.
E365913C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts and 2 nuts.


ii.
E365914

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor assembly with pulley.



b.

for Type B:

i.
E371401

Remove the 4 bolts and compressor assembly with pulley.



Hide 12602C 5.REMOVE NO. 2 ENGINE COVER

a.
A402117

Remove the 2 bolts and No. 2 engine cover from the No. 2 timing gear cover assembly.


Hide 16620D 6.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

NOTICE:
A409240

·

Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.

·

Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.



If oil or grease is on the location indicated by the arrow, replace the V-ribbed belt tensioner assembly.

a.
A400315

Remove the 2 bolts and V-ribbed belt tensioner assembly from the No. 2 timing gear cover assembly.


Hide 11336A 7.REMOVE NO. 2 TIMING CHAIN COVER INSULATOR

a.
A400316

Remove the No. 2 timing chain cover insulator from the V-ribbed belt tensioner assembly.


Hide 11336A 8.REMOVE TIMING GEAR COVER INSULATOR

a.
A402700

Using an 8 mm socket wrench, remove the bolt, plate washer and timing gear cover insulator from the No. 2 timing gear cover assembly.


Hide 11323C 9.REMOVE NO. 3 TIMING CHAIN COVER

a.
A402701

Using an 8 mm socket wrench, remove the bolt, plate washer and No. 3 timing chain cover from the No. 2 timing gear cover assembly.


Hide 16207 10.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A406740

Slide the clip and disconnect the No. 2 water by-pass pipe sub-assembly from the outlet water by-pass sub-assembly.


b.

Remove the bolt and No. 2 water by-pass pipe sub-assembly.


Hide 16260 11.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A406737

Remove the bolt to disconnect the flow shutting valve (water by-pass hose assembly).


b.
A406738

Remove the 2 bolts and the water hose clamp bracket.


c.
A406739

Slide the clip and disconnect the flow shutting valve (water by-pass hose assembly) from the outlet water by-pass sub-assembly.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (water by-pass hose assembly) and outlet water by-pass sub-assembly.



Hide 17167 12.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A404785

Remove the 5 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst).


Hide 17141 14.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

a.
A404786

Using a 12 mm deep socket wrench, remove the 7 nuts and remove the exhaust manifold (TWC: Front Catalyst) from the cylinder head sub-assembly.


b.
A404787

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 22030 15.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 16.REMOVE THROTTLE BODY GASKET

Hide 25680 17.REMOVE EGR COOLER ASSEMBLY

a.
A402702C01
1.146,0.75 1.365,0.375 1.365,0.375 1.5,0.375 true 2.333,1.281 2.552,0.906 2.552,0.906 2.688,0.906 true 2.75,0.813 3.063,1.01 0.313,0.198 10 true *1 1.573,0.271 1.885,0.469 0.313,0.198 10 true *2
*1 No. 3 Water By-pass Hose
*2 Water Hose


Disconnect the water hose from the EGR cooler assembly.


b.

Disconnect the No. 3 water by-pass hose from the EGR cooler assembly.


c.
A402703

Remove the 5 bolts, EGR cooler assembly, EGR cooler gasket and EGR valve gasket.


Hide 25687 18.REMOVE NO. 1 EGR COOLER BRACKET

a.
A402704

Remove the 2 bolts and No. 1 EGR cooler bracket from the EGR valve bracket and water outlet.


Hide 25601 19.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A402705

Using an 8 mm socket wrench, remove the 4 bolts, No. 1 EGR pipe sub-assembly, EGR inlet gasket and EGR valve adapter gasket.


Hide 20.REMOVE WATER HOSE

a.

w/ Water Hose Connector:

i.
A402230C01
0.958,2.365 1.375,2.365 false 0.802,2.271 1.052,2.5 0.25,0.229 10 true *a
*a Retainer
V100135

Pinch
V100136

Pull
V100137

Pull off


Remove the water hose from the EGR valve assembly.

Pinch the retainer of the water hose and then pull out the retainer to disengage the lock claws and pull off the water hose.



b.

w/o Water Hose Connector:

i.
A428695

Slide the clip and remove the water hose from the EGR valve assembly.



Hide 25620 21.REMOVE EGR VALVE ASSEMBLY

a.
A402706

Disconnect the clamp.


b.

Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.


c.

for EGR Valve Bracket Connection Type:

i.
A402707

Using an 8 mm socket wrench, remove the 2 bolts.


ii.
A406949C01
2.323,0.813 2.51,0.552 2.51,0.552 2.656,0.552 true 2.333,0.938 2.542,0.938 true 2.583,0.854 2.896,1.052 0.313,0.198 10 true *a 2.708,0.448 3.021,0.646 0.313,0.198 10 true *b
*a Pin
*b Hole


Remove the EGR valve assembly with the EGR valve bracket vertically.



d.

for Cylinder Head Cover Sub-assembly Connection Type:

i.
A476748

Using an 8 mm socket wrench, remove the bolt.


ii.
A476749C01
2.344,0.698 2.51,0.552 2.51,0.552 2.656,0.552 true 2.406,0.833 2.615,0.833 true 2.656,0.74 2.969,0.938 0.313,0.198 10 true *a 2.708,0.448 3.021,0.646 0.313,0.198 10 true *b
*a Pin
*b Hole


Remove the EGR valve assembly with the EGR valve bracket vertically.



e.
A402708

Using an 8 mm socket wrench, remove the bolt and EGR valve bracket.


Hide 16279 22.REMOVE NO. 3 WATER BY-PASS PIPE

a.
A402709

Using an 8 mm socket wrench, remove the bolt and No. 3 water by-pass pipe from the intake manifold.


b.

Slide the clip and disconnect the No. 3 water by-pass pipe from the water outlet.


Hide 16278 23.REMOVE NO. 2 WATER BY-PASS PIPE

a.
A402710N02
0.521,1.073 0.677,1.271 0.156,0.198 10 true B 2.073,1.896 2.229,2.094 0.156,0.198 10 true A 1.031,1.927 1.188,2.125 0.156,0.198 10 true B

Remove the bolt (A).


b.

Using an 8 mm socket wrench, remove the 2 bolts (B) and No. 2 water by-pass pipe.


Hide 17177 25.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23910A 26.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 27.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.

for EGR Valve Bracket Connection Type:

i.
A407176

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.



b.

for Cylinder Head Cover Sub-assembly Connection Type:

i.
A476750

Using an 8 mm socket wrench, remove the bolt.


ii.

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.



Hide 23100X 28.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16295 29.REMOVE NO. 7 WATER BY-PASS HOSE

a.
A402711

Slide the 2 clips and remove the No. 7 water by-pass hose.


Hide 82219A 30.REMOVE SENSOR WIRE

a.
A401308

Disconnect the 4 connectors.


b.

Disengage the 3 clamps.


c.

Using an 8 mm socket wrench, remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.


Hide 82126A 31.REMOVE NO. 6 ENGINE WIRE

a.
A401309

Disconnect the 4 connectors.


b.

Disengage the 2 clamps.


c.

Remove the 2 nuts and No. 6 engine wire from the wire harness clamp bracket.


Hide 32.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A401310

Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the No. 1 ventilation case.


Hide 23800 33.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 23807V 34.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 35.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 37.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 39.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452 42.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A400314

Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the camshaft housing sub-assembly.


c.
A400321

Remove the O-ring from the engine oil level dipstick guide.


Hide 16031 43.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 16323 44.REMOVE ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

a.
A400319

Remove the 4 bolts, engine water pump assembly (water inlet housing) and gasket from the cylinder block sub-assembly.


Hide 17169A 45.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.
A402712

Remove the 2 bolts and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.


Hide 25861A 47.REMOVE NO. 2 VACUUM SWITCHING VALVE BRACKET

a.
A402205

Using an 8 mm socket wrench, remove the 2 bolts and No. 2 vacuum switching valve bracket from the cylinder head sub-assembly.