Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2017.09–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0322783 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0717  Input/Turbine Speed Sensor "A" Circuit No Signal  P07BF  Input/Turbine Speed Sensor "A" Circuit Low  P07C0  Input/Turbine Speed Sensor "A" Circuit High  


DESCRIPTION

The input speed sensor NT detects the rotation speed of the turbine, which indicates the input shaft revolution (speed) of the transaxle. By comparing the input speed sensor NT signal with the output speed sensor NC signal, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

C370675C01
2.156,3.396 2.406,3.396 2.406,3.396 3.156,2.396 true 4.417,3.417 4.167,3.417 4.167,3.417 3.667,2.667 true 1.917,0.417 2.167,0.417 2.167,0.417 3.25,1.667 true 5,0.583 4.75,0.583 4.75,0.583 4,1.75 true 1.74,0.333 2.052,0.49 0.313,0.156 10 false *1 5.063,0.51 5.375,0.667 0.313,0.156 10 false *2 1.969,3.323 2.281,3.479 0.313,0.156 10 false *3 4.479,3.344 4.792,3.5 0.313,0.156 10 false *4
*1 Counter Gear *2 C2 Piston
*3 Output Speed Sensor NC *4 Input Speed Sensor NT


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0717 Input/Turbine Speed Sensor "A" Circuit No Signal All of the following conditions are met (1-trip detection logic):
·

The vehicle is being driven with the shift lever in D (not in 1st gear).

·

The output shaft speed is 1000 rpm or more.

·

The speed indicated by the input speed sensor NT is less than 300 rpm for 5 seconds or more.


·

Wiring harness connector

·

Transmission revolution sensor (Input speed sensor NT)

·

Transmission wire

·

ECM


Comes on DTC stored
P07BF Input/Turbine Speed Sensor "A" Circuit Low All of the following conditions are met (1-trip detection logic):
·

The battery voltage is 8 V or more.

·

The ignition switch is ON.

·

The starter is off.

·

The input speed sensor NT input voltage is less than 0.2 V for 4.5 seconds or more.


·

Wiring harness connector

·

Transmission revolution sensor (Input speed sensor NT)

·

Transmission wire

·

ECM


Comes on DTC stored
P07C0 Input/Turbine Speed Sensor "A" Circuit High All of the following conditions are met (1-trip detection logic):
·

The battery voltage is 8 V or more.

·

The ignition switch is ON.

·

The starter is off.

·

The input speed sensor NT input voltage is more than 1.8 V for 4.5 seconds.


·

Wiring harness connector

·

Transmission revolution sensor (Input speed sensor NT)

·

Transmission wire

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The NT terminal of the ECM detects a revolution signal from the input speed sensor NT (input RPM). The ECM calculates gear shifts by comparing the input speed sensor NT signal with the output speed sensor NC signal.

While the vehicle is being driven in 2nd, 3rd, 4th, 5th or 6th gear with the shift lever in D, if the input shaft revolution (speed) is less than 300 rpm*1 and the output shaft revolution (speed) is more than 1000 rpm*2, the ECM interprets this as a malfunction, illuminates the MIL and stores a DTC.

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is 50 km/h (31 mph) or more.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test and drive the vehicle for 5 seconds or more at 50 km/h (31 mph) or more.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0717, P07BF or P07C0.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C376194E01
1.115,3.656 3.229,3.875 2.115,0.219 10 false Transmission Revolution Sensor 1.615,4.156 4.948,4.51 3.333,0.354 10 false Transmission Wire 1.625,1.135 2.396,1.719 0.771,0.583 10 false Input Speed Sensor NT 1.625,2.865 2.51,3.281 0.885,0.417 10 false Output Speed Sensor NC 3.958,3.865 4.927,4.302 0.969,0.438 10 false Wiring Harness Connector 6.25,4.083 6.708,4.281 0.458,0.198 10 false C58 6.25,4.25 6.708,4.448 0.458,0.198 10 false ECM 1.292,1.208 1.75,1.406 0.458,0.198 10 false NT 1.281,2.938 1.74,3.135 0.458,0.198 10 false NC 3.115,0.708 3.573,0.906 0.458,0.198 10 false 1 3.771,0.615 4.229,0.813 0.458,0.198 10 false 1 3.771,0.823 4.229,1.021 0.458,0.198 10 false A 4.083,0.708 4.542,0.906 0.458,0.198 10 false NTB 4.542,0.708 5,0.906 0.458,0.198 10 false NTB 5.906,0.708 6.365,0.906 0.458,0.198 10 false NTB 5.531,0.708 5.99,0.906 0.458,0.198 10 false 126 5,0.604 5.458,0.802 0.458,0.198 10 false 1 4.927,0.823 5.385,1.021 0.458,0.198 10 false C54 4.938,1.604 5.396,1.802 0.458,0.198 10 false C54 4.938,2.552 5.396,2.75 0.458,0.198 10 false C54 4.938,3.323 5.396,3.521 0.458,0.198 10 false C54 5.896,1.49 6.354,1.688 0.458,0.198 10 false NTO 5.885,2.438 6.344,2.635 0.458,0.198 10 false NCB 5.906,3.219 6.365,3.417 0.458,0.198 10 false NCO 6.531,0.552 6.99,0.75 0.458,0.198 10 false 12 V 6.542,2.292 7,2.49 0.458,0.198 10 false 12 V 3.771,1.604 4.229,1.802 0.458,0.198 10 false A 3.781,2.552 4.24,2.75 0.458,0.198 10 false A 3.771,3.323 4.229,3.521 0.458,0.198 10 false A 5.531,1.479 5.99,1.677 0.458,0.198 10 false 125 5.604,2.427 6.063,2.625 0.458,0.198 10 false 75 5.615,3.219 6.073,3.417 0.458,0.198 10 false 74 3.115,1.49 3.573,1.688 0.458,0.198 10 false 2 3.115,2.438 3.573,2.635 0.458,0.198 10 false 4 3.115,3.208 3.573,3.406 0.458,0.198 10 false 3 3.771,1.385 4.229,1.583 0.458,0.198 10 false 2 3.781,2.344 4.24,2.542 0.458,0.198 10 false 4 3.792,3.115 4.25,3.313 0.458,0.198 10 false 3 4.531,1.49 4.99,1.688 0.458,0.198 10 false NTO 4.063,1.479 4.521,1.677 0.458,0.198 10 false NTO 4.063,2.438 4.521,2.635 0.458,0.198 10 false NCB 4.531,2.438 4.99,2.635 0.458,0.198 10 false NCB 4.063,3.208 4.521,3.406 0.458,0.198 10 false NCO 4.51,3.208 4.969,3.406 0.458,0.198 10 false NCO 5.021,2.344 5.479,2.542 0.458,0.198 10 false 4 5.01,3.115 5.469,3.313 0.458,0.198 10 false 3 5.01,1.385 5.469,1.583 0.458,0.198 10 false 2 2.708,0.719 3.167,0.917 0.458,0.198 10 false NTB 2.708,1.479 3.167,1.677 0.458,0.198 10 false NTO 2.708,2.438 3.167,2.635 0.458,0.198 10 false NCB 2.708,3.219 3.167,3.417 0.458,0.198 10 false NCO

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NT) Input turbine speed Min.: 0 rpm
Max.: 12750 rpm
·

Equal to engine speed:

Lock-up on (after warming up the engine)

·

Nearly equal to engine speed:

Lock-up off (engine idling with shift lever in N)


Data is displayed in increments of 50 rpm
Powertrain > Engine and ECT > Data List
Tester Display
SPD (NT)
50003 234 390
HINT:
·

SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor malfunction, improper installation or intermittent connection malfunction in the circuit.





PROCEDURE

1.READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NT) Input turbine speed Min.: 0 rpm
Max.: 12750 rpm
·

Equal to engine speed:

Lock-up on (after warming up the engine)

·

Nearly equal to engine speed:

Lock-up off (engine idling with shift lever in N)


Data is displayed in increments of 50 rpm
NT Sensor Voltage Input turbine speed sensor output voltage Min.: 0 V
Max.: 4.999 V
0.1 to 1.9 V -
Powertrain > Engine and ECT > Data List
Tester Display
SPD (NT)
NT Sensor Voltage
50003 234 390,391

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

B

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
a.
C376061C01
1.5,0.115 1.917,0.365 0.417,0.25 0.771,1.813 1.188,1.146 true 1.74,1.813 1.323,1.146 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.156 1.896,0.354 0.313,0.198 10 false C54 0.625,1.833 1.083,2.031 0.458,0.198 10 false NTB 1.635,1.833 2.094,2.031 0.458,0.198 10 false NTO
*a Front view of wire harness connector
(to Wiring Harness Connector)


Disconnect the C54 wiring harness connector connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-2 (NTO) - Body ground Always 99 to 101 Ω


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C54-1 (NTB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT WIRING HARNESS CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
3.INSPECT WIRING HARNESS CONNECTOR

b.

Measure the resistance according to the value(s) in the table below.

C267935C30
1.115,0.698 1.51,0.917 0.396,0.219 5.615,0.698 6.01,0.917 0.396,0.219 0.833,2.01 1.094,1.24 true 1.427,2.021 1.229,1.24 true 6.594,1.948 6.438,1.323 true 6.177,1.948 6.313,1.323 true 2.604,0.125 2.917,0.323 0.313,0.198 10 false *1 0.354,0.625 0.667,0.823 0.313,0.198 10 false *a 4.875,0.625 5.188,0.823 0.313,0.198 10 false *b 6.49,1.969 6.885,2.167 0.396,0.198 10 false NTB 1.313,2.031 1.708,2.229 0.396,0.198 10 false NTO 6.042,1.969 6.438,2.167 0.396,0.198 10 false NTO 0.688,2.031 1.083,2.229 0.396,0.198 10 false NTB 1.26,0.729 1.656,0.927 0.396,0.198 10 false A 5.688,0.729 6.083,0.927 0.396,0.198 10 false C54
*1 Wiring Harness Connector - -
*a Transmission wire side *b ECM side


Standard Resistance:
Tester Connection Condition Specified Condition
C54-1 (NTB) - A-1 (NTB) Always Below 1 Ω
C54-2 (NTO) - A-2 (NTO) Always Below 1 Ω
C54-1 (NTB) or A-1 (NTB) - Other terminals Always 10 kΩ or higher
C54-2 (NTO) A-2 (NTO) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)

NG

4.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)
a.

Remove the transmission valve body assembly.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL


b.
C133219

Make sure that the connector is properly connected, and check the transmission revolution sensor installation.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>INSTALLATION

OK:

The installation bolts are tightened properly and there is no clearance between the transmission revolution sensor and transmission valve body assembly.



Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION WIRE

NG

REPAIR OR REPLACE TRANSMISSION REVOLUTION SENSOR

5.INSPECT TRANSMISSION WIRE
a.
C275092C01
2.677,1.208 3,1.469 0.323,0.26 1.938,1.042 1.333,2.167 false 2.083,1.042 2.25,2.167 false 1.458,3.948 1,4.333 false 1.688,3.938 2,4.333 false 0.073,0.094 0.385,0.25 0.313,0.156 10 *a 0.5,0.5 0.813,0.656 0.313,0.156 10 *b 0.583,3.094 0.896,3.25 0.313,0.156 10 *c 2.802,1.25 2.958,1.448 0.156,0.198 10 A 1.208,2.198 1.667,2.396 0.458,0.198 10 NTO 2.125,2.198 2.583,2.396 0.458,0.198 10 NTB 0.875,4.365 1.333,4.563 0.458,0.198 10 NTB 1.875,4.365 2.333,4.563 0.458,0.198 10 NTO
*a Component without harness connected
(Transmission Wire)
*b Wiring harness connector side
*c Transmission revolution sensor side


Disconnect the transmission revolution sensor connector from the transmission wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NTB) sensor side - A-1 (NTB) wiring harness connector side Always Below 1 Ω
2 (NTO) sensor side - A-2 (NTO) wiring harness connector side Always Below 1 Ω
1 (NTB) sensor side or A-1 (NTB) wiring harness connector side - Body ground and other terminals Always 10 kΩ or higher
2 (NTO) sensor side or A-2 (NTO) wiring harness connector side - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the C58 ECM connector.


b.

Disconnect the C54 wiring harness connector connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-1 (NTB) - C58-126 (NTB) Always Below 1 Ω
C54-2 (NTO) - C58-125 (NTO) Always Below 1 Ω
C54-1 (NTB) or C58-126 (NTB) - Body ground and other terminals Always 10 kΩ or higher
C54-2 (NTO) or C58-125 (NTO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR