The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during automatic transaxle assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
| *a | An Object Exceeding Weight Limit of Transmission Jack |
The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.
11361J
1.REMOVE FLYWHEEL HOUSING UNDER COVER
32101A
2.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.
There will be one black colored drive plate and torque converter assembly setting bolt.
3.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
28100
4.REMOVE STARTER ASSEMBLY
5.DISCONNECT WIRE HARNESS
Disengage the claw, rotate the lever and disconnect the transmission wire connector.
Disconnect the park/neutral position switch assembly connector.
for LHD:
Disconnect the rack and pinion power steering gear assembly connector.
Release the lock before rotating the lock lever.
Remove the 2 bolts to disconnect the wire harness.
Disengage the 2 wire harness clamps to disconnect the wire harness.
for RHD:
Disconnect the rack and pinion power steering gear assembly connector.
Release the lock before rotating the lock lever.
Remove the bolt to disconnect the wire harness.
Disengage the wire harness clamp to disconnect the wire harness.
Disengage the 2 wire harness clamps to disconnect the wire harness.
Remove the 2 bolts to disconnect the 2 earth wires from the automatic transaxle assembly.
82824D
6.REMOVE WIRING HARNESS CONNECTOR
Remove the 2 bolts.
Remove the wiring harness connector from the transaxle case sub-assembly.
32942
7.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE
32941
8.DISCONNECT INLET NO. 1 OIL COOLER HOSE
33493A
9.REMOVE TRANSMISSION OIL COOLER
32942
10.REMOVE OUTLET NO. 1 OIL COOLER HOSE
Slide the clip and remove the outlet No. 1 oil cooler hose from the oil cooler tube union (outlet).
Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and oil cooler tube union (outlet).
32941
11.REMOVE INLET NO. 1 OIL COOLER HOSE
Slide the clip and remove the inlet No. 1 oil cooler hose from the oil cooler tube union (inlet).
Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and oil cooler tube union (inlet).
12.INSTALL ENGINE HANGERS
51100G
13.REMOVE FRONT FRAME ASSEMBLY
12311A
14.REMOVE FRONT ENGINE MOUNTING BRACKET
Remove the 3 bolts and front engine mounting bracket from the transaxle housing.
30500
15.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY
Support the automatic transaxle assembly with a transmission jack.
Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.
Remove the 9 bolts and automatic transaxle assembly.
To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.
12372A
16.REMOVE ENGINE MOUNTING INSULATOR LH
Remove the 4 bolts and engine mounting insulator LH from the transaxle case sub-assembly.
12371A
17.REMOVE REAR ENGINE MOUNTING INSULATOR
12303
18.REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY
Remove the 4 bolts and rear engine mounting bracket sub-assembly from the transaxle housing.
33823
19.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the transaxle case sub-assembly.
35150
20.REMOVE TRANSMISSION CASE PLUG ASSEMBLY
Remove the transmission case plug assembly from the transaxle housing.
Remove the O-ring from the transmission case plug assembly.
21.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the bolt and wire harness clamp bracket from the transaxle case sub-assembly.
32000
22.REMOVE TORQUE CONVERTER ASSEMBLY
Remove the torque converter assembly from the automatic transaxle assembly.
32000
23.INSPECT TORQUE CONVERTER ASSEMBLY
32101
24.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY