Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (except 2AR-FE) › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0326623 DYNAMIC RADAR CRUISE CONTROL SYSTEM(except 2AR-FE) J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(except 2AR-FE)  Distance Control Switch Circuit  


DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

A402879E06
1.25,0.729 2.927,1.094 1.677,0.365 10 false Vehicle-to-vehicle Distance Control Switch 2.573,0.458 3.188,0.656 0.615,0.198 10 false DIST 2.573,1.917 3.188,2.115 0.615,0.198 10 false ECC 0.938,2.646 2.979,2.865 2.042,0.219 10 false Steering Pad Switch Assembly 3.073,0.594 3.688,0.792 0.615,0.198 10 false z1 3.073,2.042 3.688,2.24 0.615,0.198 10 false z1 3.104,0.365 3.719,0.563 0.615,0.198 10 false 8 3.063,1.802 3.677,2 0.615,0.198 10 false 12 3.802,0.469 4.417,0.667 0.615,0.198 10 false DIST 3.833,1.896 4.448,2.094 0.615,0.198 10 false ECC 3.135,2.656 5.177,2.875 2.042,0.219 10 false Spiral Cable Sub-assembly 4.271,0.604 4.885,0.802 0.615,0.198 10 false K22 4.281,2.052 4.896,2.25 0.615,0.198 10 false K22 4.344,0.365 4.958,0.563 0.615,0.198 10 false 6 4.365,1.823 4.979,2.021 0.615,0.198 10 false 2 5.688,0.594 6.302,0.792 0.615,0.198 10 false LKSW 5.365,1.198 6.646,1.563 1.281,0.365 10 false Forward Recognition Camera 5.104,1.198 5.719,1.396 0.615,0.198 10 false V6 5.479,0.469 6.094,0.667 0.615,0.198 10 false 3 5.865,3.01 6.5,3.208 0.635,0.198 10 false ECM 5.51,3 6.146,3.198 0.635,0.198 10 false A24 5.667,2.052 6.302,2.25 0.635,0.198 10 false ECCS 5.667,2.563 6.302,2.76 0.635,0.198 10 false E1 5.427,1.948 6.042,2.146 0.615,0.198 10 false 28 5.427,2.427 6.042,2.625 0.615,0.198 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Distance Control Switch Distance control switch signal ON or OFF ON: Distance control switch on
OFF: Distance control switch off
-
Powertrain > Radar Cruise2 > Data List
Tester Display
Distance Control Switch
50003 197 5
OK:

When the vehicle-to-vehicle distance control switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA, ECM AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA, ECM AND BODY GROUND)
a.

Disconnect the K22 spiral cable sub-assembly connector.


b.

Disconnect the V6 forward recognition camera connector.


c.

Disconnect the A24 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-6 (DIST) - V6-3 (LKSW) Always Below 1 Ω
K22-2 (ECC) - A24-28 (ECCS) Always Below 1 Ω
K22-6 (DIST) or V6-3 (LKSW) - Body ground Always 10 kΩ or higher
K22-2 (ECC) or A24-28 (ECCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the A24 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-10 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK ECM (ECM TERMINALS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (ECM TERMINALS)
a.
A402881C01
1.479,0.135 1.917,0.365 0.438,0.229 2.885,1.375 2.594,1.375 2.594,1.375 2.323,1.063 true 0.531,0.917 1.042,0.917 true 0.094,0.125 0.406,0.281 0.313,0.156 10 false *a 1.573,0.177 2.031,0.375 0.458,0.198 10 false A24 0.333,0.833 0.646,1.031 0.313,0.198 10 false E1 2.927,1.292 3.365,1.469 0.438,0.177 10 false ECCS
*a Component without harness connected
(ECM)


Disconnect the A24 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-28 (ECCS) - A24-10 (E1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG