Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2017.09–2018.04
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327341 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/o Occupant Classification System)

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.

·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.

Visually check the spiral cable sub-assembly for defects.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.

Check the spiral cable sub-assembly.

B479846C02
6.365,0.844 6.656,1.052 0.292,0.208 2.208,3.354 2.542,3.563 0.333,0.208 0.313,3.542 0.646,3.75 0.333,0.208 3.135,1.01 3.427,1.208 0.292,0.198 1.365,1.531 1.646,1.74 0.281,0.208 4.365,0.844 4.656,1.052 0.292,0.208 1.781,3.552 1.073,2.854 false 5.625,1.385 5.615,1.021 false 1.906,3.448 2.177,3.219 false 5.073,0.333 5.5,0.885 false 1.896,3.552 2.208,3.708 false 5.49,0.344 5.604,0.885 false 1.781,3.656 1.167,4.385 false 6.021,1.396 5.719,1.021 false 1.896,3.646 2.198,3.896 false 5.854,0.344 5.719,0.885 false 1.781,3.354 1.417,2.854 false 1.115,3.438 0.604,3.021 false 1.115,3.625 0.604,3.292 false 3.615,1.146 3.313,1.448 false 2.906,1.146 3.229,1.448 false 1.896,3.76 2.208,4.094 false 6.229,0.344 5.833,0.885 false 5.094,1.031 5.219,1.406 5.219,1.406 5.385,1.031 false 1.781,3.76 1.521,4.365 false 6.406,1.406 5.833,1.021 false 1.896,3.354 2.229,2.99 false 4.656,0.333 5.396,0.906 false 1.896,3.854 2.292,4.375 false 6.563,0.344 5.958,0.885 false 1.792,3.854 1.979,4.375 false 1.625,1.177 1.875,1.417 false 4.552,0.583 4.99,0.885 false 4.813,1.406 4.99,1.021 false 1.781,3.25 1.844,2.854 false 1.896,3.25 2.229,2.854 false 2.26,3.375 2.792,3.792 0.531,0.417 10 false K22 0.927,2.698 1.417,2.948 0.49,0.25 10 false EAU 5.479,1.417 5.969,1.667 0.49,0.25 10 false EAU 6.458,0.875 6.917,1.073 0.458,0.198 10 false z1 2.229,3.125 2.719,3.375 0.49,0.25 10 false +DP2 4.875,0.177 5.365,0.427 0.49,0.25 10 false +DP2 2.25,3.635 2.74,3.885 0.49,0.25 10 false +DP 5.323,0.177 5.813,0.427 0.49,0.25 10 false +DP 1.01,4.396 1.5,4.646 0.49,0.25 10 false AU2 5.896,1.417 6.385,1.667 0.49,0.25 10 false AU2 2.25,3.833 2.74,4.083 0.49,0.25 10 false AU1 5.729,0.177 6.219,0.427 0.49,0.25 10 false AU1 1.281,2.698 1.771,2.948 0.49,0.25 10 false ECC 0.365,3.563 0.854,3.813 0.49,0.25 10 false K24 0.406,2.927 0.896,3.177 0.49,0.25 10 false D+ 0.427,3.219 0.917,3.469 0.49,0.25 10 false D- 3.219,1.031 3.688,1.313 0.469,0.281 10 false z9 3.656,1.063 4.146,1.313 0.49,0.25 10 false D+ 2.719,1.063 3.208,1.313 0.49,0.25 10 false D- 2.25,4.031 2.74,4.281 0.49,0.25 10 false CCS 6.104,0.177 6.594,0.427 0.49,0.25 10 false CCS 5.073,1.417 5.563,1.667 0.49,0.25 10 false ECC 1.365,4.396 1.854,4.646 0.49,0.25 10 false DIST 6.281,1.417 6.771,1.667 0.49,0.25 10 false DIST 2.271,2.885 2.76,3.135 0.49,0.25 10 false IL-2 4.521,0.177 5.01,0.427 0.49,0.25 10 false IL-2 2.219,4.396 2.708,4.646 0.49,0.25 10 false IL+2 6.479,0.177 6.969,0.427 0.49,0.25 10 false IL+2 1.896,4.396 2.385,4.646 0.49,0.25 10 false HO 1.396,1.083 1.885,1.333 0.49,0.25 10 false HO 1.469,1.563 1.958,1.813 0.49,0.25 10 false A 0.094,0.104 0.677,0.49 0.583,0.385 10 false *a 4.229,0.5 4.719,0.75 0.49,0.25 10 false SUP 4.667,1.417 5.156,1.667 0.49,0.25 10 false SDN 4.448,0.875 4.906,1.073 0.458,0.198 10 false z4 1.708,2.698 2.198,2.948 0.49,0.25 10 false SDN 2.104,2.698 2.594,2.948 0.49,0.25 10 false SUP
*a Component without harness connected
(Spiral Cable Sub-assembly)
- -
V100144

Interlock - -


NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



i.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-1 (SDN) - z4-4 (SDN) Always 3 Ω or less
K22-2 (ECC) - z4-3 (ECC) Always 3 Ω or less
K22-2 (ECC) - z1-12 (ECC) Always 3 Ω or less
K22-4 (EAU) - z1-10 (EAU) Always 3 Ω or less
K22-5 (AU2) - z1-9 (AU2) Always 3 Ω or less
K22-6 (DIST) - z1-8 (DIST) Always 3 Ω or less
K22-7 (HO) - A (HO) Always 3 Ω or less
K22-8 (SUP) - z4-2 (SUP) Always 3 Ω or less
K22-9 (IL-2) - z1-6 (IL-2) Always 3 Ω or less
K22-10 (+DP2) - z1-5 (+DP2) Always 3 Ω or less
K22-11 (+DP) - z1-4 (+DP) Always 3 Ω or less
K22-12 (AU1) - z1-3 (AU1) Always 3 Ω or less
K22-13 (CCS) - z1-2 (CCS) Always 3 Ω or less
K22-14 (IL+2) - z1-1 (IL+2) Always 3 Ω or less
K24-1 (D+) - z9-2 (D+) Always Below 1 Ω
K24-2 (D-) - z9-1 (D-) Always Below 1 Ω



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-1 (SDN) - z4-4 (SDN) Always 3 Ω or less
K22-2 (ECC) - z4-3 (ECC) Always 3 Ω or less
K22-2 (ECC) - z1-12 (ECC) Always 3 Ω or less
K22-4 (EAU) - z1-10 (EAU) Always 3 Ω or less
K22-5 (AU2) - z1-9 (AU2) Always 3 Ω or less
K22-6 (DIST) - z1-8 (DIST) Always 3 Ω or less
K22-7 (HO) - A (HO) Always 3 Ω or less
K22-8 (SUP) - z4-2 (SUP) Always 3 Ω or less
K22-9 (IL-2) - z1-6 (IL-2) Always 3 Ω or less
K22-10 (+DP2) - z1-5 (+DP2) Always 3 Ω or less
K22-11 (+DP) - z1-4 (+DP) Always 3 Ω or less
K22-12 (AU1) - z1-3 (AU1) Always 3 Ω or less
K22-13 (CCS) - z1-2 (CCS) Always 3 Ω or less
K22-14 (IL+2) - z1-1 (IL+2) Always 3 Ω or less
K24-1 (D+) - z9-2 (D+) Always Below 1 Ω
K24-2 (D-) - z9-1 (D-) Always Below 1 Ω



iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-1 (SDN) - z4-4 (SDN) Always 3 Ω or less
K22-2 (ECC) - z4-3 (ECC) Always 3 Ω or less
K22-2 (ECC) - z1-12 (ECC) Always 3 Ω or less
K22-4 (EAU) - z1-10 (EAU) Always 3 Ω or less
K22-5 (AU2) - z1-9 (AU2) Always 3 Ω or less
K22-6 (DIST) - z1-8 (DIST) Always 3 Ω or less
K22-7 (HO) - A (HO) Always 3 Ω or less
K22-8 (SUP) - z4-2 (SUP) Always 3 Ω or less
K22-9 (IL-2) - z1-6 (IL-2) Always 3 Ω or less
K22-10 (+DP2) - z1-5 (+DP2) Always 3 Ω or less
K22-11 (+DP) - z1-4 (+DP) Always 3 Ω or less
K22-12 (AU1) - z1-3 (AU1) Always 3 Ω or less
K22-13 (CCS) - z1-2 (CCS) Always 3 Ω or less
K22-14 (IL+2) - z1-1 (IL+2) Always 3 Ω or less
K24-1 (D+) - z9-2 (D+) Always Below 1 Ω
K24-2 (D-) - z9-1 (D-) Always Below 1 Ω


If the result is not as specified, replace the spiral cable sub-assembly.



Hide 2.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/ Occupant Classification System)

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.

·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.

Visually check the spiral cable sub-assembly for defects.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.

Check the spiral cable sub-assembly.

B472869C02
0.333,3.604 0.656,3.833 0.323,0.229 1.771,1.406 2.094,1.635 0.323,0.229 2.719,1.406 3.042,1.635 0.323,0.229 2.208,3.396 2.531,3.625 0.323,0.229 6.396,0.813 6.719,1.042 0.323,0.229 0.635,1.542 0.958,1.771 0.323,0.229 2.667,1.833 2.344,1.646 false 3.573,1.833 3.271,1.646 false 1.125,3.438 0.625,3.188 false 1.115,3.625 0.604,3.417 false 1.115,3.792 0.656,3.99 false 1.115,3.979 0.677,4.229 false 2.167,1.156 2.292,1.448 false 2.531,1.146 2.375,1.448 false 3.469,1.146 3.313,1.448 false 3.104,1.146 3.229,1.438 false 1.781,3.344 1.615,2.896 false 1.781,3.552 1.219,2.896 false 1.781,3.656 1.146,4.365 false 1.896,3.75 2.24,4.198 false 1.781,3.76 1.51,4.365 false 1.781,3.854 1.865,4.375 false 1.896,3.854 2.198,4.365 false 1.896,3.656 2.24,3.969 false 1.896,3.563 2.24,3.771 false 1.896,3.354 2.271,2.927 false 1.906,3.448 2.208,3.188 false 5.5,0.885 5.031,0.385 false 5.615,0.885 5.406,0.385 false 5.719,0.885 5.813,0.385 false 5.833,0.885 6.156,0.385 false 5.948,0.885 6.521,0.385 false 5.615,1.021 5.563,1.385 false 5.729,1.021 5.938,1.396 false 5.833,1.021 6.323,1.396 false 1.073,1.521 0.75,1.271 false 4.625,0.385 5.365,0.875 false 5.385,1.021 5.188,1.385 false 0.104,0.063 0.573,0.469 0.469,0.406 10 false *a 2.698,1.75 3.333,2.313 0.635,0.563 10 false *b 3.615,1.75 4.115,2.167 0.5,0.417 10 false *c 0.385,3.635 0.75,3.854 0.365,0.219 10 false K24 0.417,3.104 0.781,3.323 0.365,0.219 10 false D+ 0.417,3.333 0.781,3.552 0.365,0.219 10 false D- 0.396,3.917 0.76,4.135 0.365,0.219 10 false D2- 0.396,4.156 0.76,4.375 0.365,0.219 10 false D2+ 2.094,0.99 2.458,1.208 0.365,0.219 10 false D- 2.469,0.99 2.833,1.208 0.365,0.219 10 false D+ 3.396,0.99 3.76,1.208 0.365,0.219 10 false D2+ 3,0.99 3.365,1.208 0.365,0.219 10 false D2- 1.865,1.438 2.229,1.656 0.365,0.219 10 false z2 2.813,1.438 3.177,1.656 0.365,0.219 10 false z3 2.26,3.427 2.625,3.646 0.365,0.219 10 false K22 1.469,2.74 1.885,2.969 0.417,0.229 10 false ECC 1.083,2.74 1.5,2.969 0.417,0.229 10 false EAU 1,4.375 1.417,4.604 0.417,0.229 10 false AU2 1.354,4.375 1.771,4.604 0.417,0.229 10 false DIST 1.76,4.375 2.177,4.604 0.417,0.229 10 false HO 2.094,4.375 2.51,4.604 0.417,0.229 10 false IL+2 2.281,4.135 2.698,4.365 0.417,0.229 10 false CCS 2.281,3.906 2.698,4.135 0.417,0.229 10 false AU1 2.281,3.698 2.698,3.927 0.417,0.229 10 false +DP 2.24,3.104 2.76,3.333 0.521,0.229 10 false +DP2 2.313,2.844 2.833,3.073 0.521,0.229 10 false IL-2 6.49,0.844 6.844,1.063 0.354,0.219 10 false z1 4.5,0.229 5.021,0.458 0.521,0.229 10 false IL-2 4.833,0.229 5.354,0.458 0.521,0.229 10 false +DP2 5.667,0.229 6.188,0.458 0.521,0.229 10 false AU1 5.26,0.229 5.781,0.458 0.521,0.229 10 false +DP 6.021,0.229 6.542,0.458 0.521,0.229 10 false CCS 6.406,0.229 6.927,0.458 0.521,0.229 10 false IL+2 5.042,1.396 5.458,1.625 0.417,0.229 10 false ECC 5.417,1.396 5.833,1.625 0.417,0.229 10 false EAU 5.802,1.396 6.219,1.625 0.417,0.229 10 false AU2 6.198,1.396 6.615,1.625 0.417,0.229 10 false DIST 0.521,1.188 0.938,1.417 0.417,0.229 10 false HO 0.75,1.573 1.115,1.792 0.365,0.219 10 false A
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Color: Light Green
*c Color: Black - -
V100144

Interlock - -


NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



i.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-2 (ECC) - z1-12 (ECC) Always 3 Ω or less
K22-4 (EAU) - z1-10 (EAU) Always 3 Ω or less
K22-5 (AU2) - z1-9 (AU2) Always 3 Ω or less
K22-6 (DIST) - z1-8 (DIST) Always 3 Ω or less
K22-7 (HO) - A (HO) Always 3 Ω or less
K22-9 (IL-2) - z1-6 (IL-2) Always 3 Ω or less
K22-10 (+DP2) - z1-5 (+DP2) Always 3 Ω or less
K22-11 (+DP) - z1-4 (+DP) Always 3 Ω or less
K22-12 (AU1) - z1-3 (AU1) Always 3 Ω or less
K22-13 (CCS) - z1-2 (CCS) Always 3 Ω or less
K22-14 (IL+2) - z1-1 (IL+2) Always 3 Ω or less
K24-1 (D+) - z2-2 (D+) Always Below 1 Ω
K24-2 (D-) - z2-1 (D-) Always Below 1 Ω
K24-3 (D2-) - z3-1 (D2-) Always Below 1 Ω
K24-4 (D2+) - z3-2 (D2+) Always Below 1 Ω



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-2 (ECC) - z1-12 (ECC) Always 3 Ω or less
K22-4 (EAU) - z1-10 (EAU) Always 3 Ω or less
K22-5 (AU2) - z1-9 (AU2) Always 3 Ω or less
K22-6 (DIST) - z1-8 (DIST) Always 3 Ω or less
K22-7 (HO) - A (HO) Always 3 Ω or less
K22-9 (IL-2) - z1-6 (IL-2) Always 3 Ω or less
K22-10 (+DP2) - z1-5 (+DP2) Always 3 Ω or less
K22-11 (+DP) - z1-4 (+DP) Always 3 Ω or less
K22-12 (AU1) - z1-3 (AU1) Always 3 Ω or less
K22-13 (CCS) - z1-2 (CCS) Always 3 Ω or less
K22-14 (IL+2) - z1-1 (IL+2) Always 3 Ω or less
K24-1 (D+) - z2-2 (D+) Always Below 1 Ω
K24-2 (D-) - z2-1 (D-) Always Below 1 Ω
K24-3 (D2-) - z3-1 (D2-) Always Below 1 Ω
K24-4 (D2+) - z3-2 (D2+) Always Below 1 Ω



iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-2 (ECC) - z1-12 (ECC) Always 3 Ω or less
K22-4 (EAU) - z1-10 (EAU) Always 3 Ω or less
K22-5 (AU2) - z1-9 (AU2) Always 3 Ω or less
K22-6 (DIST) - z1-8 (DIST) Always 3 Ω or less
K22-7 (HO) - A (HO) Always 3 Ω or less
K22-9 (IL-2) - z1-6 (IL-2) Always 3 Ω or less
K22-10 (+DP2) - z1-5 (+DP2) Always 3 Ω or less
K22-11 (+DP) - z1-4 (+DP) Always 3 Ω or less
K22-12 (AU1) - z1-3 (AU1) Always 3 Ω or less
K22-13 (CCS) - z1-2 (CCS) Always 3 Ω or less
K22-14 (IL+2) - z1-1 (IL+2) Always 3 Ω or less
K24-1 (D+) - z2-2 (D+) Always Below 1 Ω
K24-2 (D-) - z2-1 (D-) Always Below 1 Ω
K24-3 (D2-) - z3-1 (D2-) Always Below 1 Ω
K24-4 (D2+) - z3-2 (D2+) Always Below 1 Ω


If the result is not as specified, replace the spiral cable sub-assembly.