Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
After the main body ECU (multiplex network body ECU) has been replaced, the automatic light control system will not operate until the engine is started.
1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Make sure that the connecting surfaces are free of foreign matter.
Do not touch the main body ECU (multiplex network body ECU) connector.
| *a | 20° or more |
| *b | Housing Sidewall |
|
Set in this Direction |
Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the instrument panel junction block assembly as shown in the illustration.
Make sure to keep the angle at 20° or more as shown in the illustration.
| *a | Housing Sidewall |
|
Slide in this Direction |
Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the 2 guides.
| *a | Side A |
|
Install in this Direction |
While keeping the main body ECU (multiplex network body ECU) in contact with side A of the instrument panel junction block assembly (axis of rotation), lower it as shown in the illustration.
| *1 | Instrument Panel Junction Block Assembly |
| *2 | Main Body ECU (Multiplex Network Body ECU) |
|
Push Area |
Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).
Make sure to press only the push area.
Confirm the engagement of the main body ECU (multiplex network body ECU) and instrument panel junction block assembly by listening for the click sound of the lock engaging.
If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and instrument panel junction block assembly are flush.
82715
2.INSTALL WIRING HARNESS CLAMP BRACKET
Engage the guide.
Install the wiring harness clamp bracket with the nut.
3.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
for LHD:
|
Install in this Direction |
Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.
Be sure to connect the connector securely.
Engage the clamp.
Engage the clamp.
|
Install in this Direction |
Engage the claw and guide to install the instrument panel junction block assembly with main body ECU.
Install the 2 nuts.
|
Install in this Direction |
Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.
Be sure to connect the connector securely.
Engage the clamp.
Connect each connector.
for RHD:
|
Install in this Direction |
Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.
Be sure to connect the connector securely.
Engage the clamp.
Engage the clamp.
|
Install in this Direction |
Engage the claw and guide to install the instrument panel junction block assembly with main body ECU.
Engage the clamp.
Install the 2 nuts.
|
Install in this Direction |
Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.
Be sure to connect the connector securely.
Connect each connector.
55308B
4.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD)
73900
5.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)
55303B
6.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION
55476C
7.INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>INSTALLATION
55012A
8.INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>INSTALLATION
55435B
9.INSTALL NO. 1 METER HOOD CLUSTER (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>INSTALLATION
55607
10.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
55318C
11.INSTALL INSTRUMENT SIDE PANEL LH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION
62312B
12.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION
62112A
13.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
67914
14.INSTALL FRONT DOOR SCUFF PLATE LH (for RHD)
Use the same procedure for RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
for 2AR-FE:
Click hereGeneral>MAINTENANCE>2AR-FE BATTERY>INSTALLATION
for A25A-FKS:
Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>INSTALLATION
for 2GR-FKS:
16.INSPECT SRS WARNING LIGHT