Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320457 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B1279  Lost Communication with Humidity/Rain Sensor LIN  


DESCRIPTION

The main body ECU (multiplex network body ECU) and rain sensor communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from
B1279 Lost Communication with Humidity/Rain Sensor LIN
Detection Condition:

Battery voltage is 9.5 V or more


Malfunction Status:

Communication malfunction with rain sensor


Malfunction Duration:

10 seconds or more


·

Rain sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


○ Main Body

WIRING DIAGRAM

E377971E01
1.229,0.333 2.917,0.531 1.688,0.198 10 false from IG1 NO. 1 Relay 2.292,1.104 3.979,1.302 1.688,0.198 10 false LIN3 3.698,0.51 5.385,0.708 1.688,0.198 10 false ECU-IG1 NO. 3 0.146,1.583 1.833,1.781 1.688,0.198 10 false I86 0.146,1.74 3.208,1.979 3.063,0.24 10 false Main Body ECU (Multiplex Network Body ECU) 0.875,2.375 2.563,2.573 1.688,0.198 10 false : LIN Communication Line 5.469,2.146 6.542,2.344 1.073,0.198 10 false P2 5.479,2.313 6.365,2.521 0.885,0.208 10 false Rain Sensor 5.51,0.354 6.344,0.583 0.833,0.229 10 false SIG 5.5,1.104 6.333,1.333 0.833,0.229 10 false MPX 5.5,1.677 6.333,1.906 0.833,0.229 10 false ES 2.677,0.948 2.875,1.156 0.198,0.208 10 false 3 5.313,0.948 5.51,1.156 0.198,0.208 10 false 3 5.313,0.24 5.51,0.448 0.198,0.208 10 false 4 5.313,1.563 5.51,1.771 0.198,0.208 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


e.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only DTC B1279 is output A
DTC B1279 and B1373 are output B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - RAIN SENSOR)

B

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - RAIN SENSOR)
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the V4*1 or V5*2 rain sensor connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K51-3 (LIN3) - V4-3 (MPX) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
K51-3 (LIN3) - V5-3 (MPX) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
E366392C01
1.5,0.25 1.917,0.5 0.417,0.25 0.76,1.646 1.167,0.917 false 1.594,0.292 2,0.531 0.406,0.24 10 false K51 0.604,1.719 0.938,1.917 0.333,0.198 10 false LIN3 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Main Body ECU (Multiplex Network Body ECU)


a.

Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K51-3 (LIN3) - Body ground Ignition switch off Below 1 V
Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - RAIN SENSOR)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - RAIN SENSOR)
E267170C50
0.323,0.688 0.729,0.938 0.406,0.25 0.333,1.052 0.74,1.302 0.406,0.25 2,1.365 2.5,1.667 true 0.135,0.156 0.448,0.354 0.313,0.198 10 false *a 2.542,1.656 2.906,1.854 0.365,0.198 10 false SIG 0.438,0.729 0.75,0.927 0.313,0.198 10 false V4 0.823,0.719 1.135,0.917 0.313,0.198 10 false *A 0.448,1.094 0.76,1.292 0.313,0.198 10 false V5 0.833,1.073 1.146,1.271 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Rain Sensor)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
V4-4 (SIG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
V5-4 (SIG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BODY GROUND)
E267170C49
0.323,0.688 0.729,0.938 0.406,0.25 0.333,1.052 0.74,1.302 0.406,0.25 1.583,1.396 1.073,1.729 true 0.135,0.156 0.448,0.354 0.313,0.198 10 false *a 0.896,1.698 1.208,1.896 0.313,0.198 10 false ES 0.438,0.729 0.75,0.927 0.313,0.198 10 false V4 0.823,0.719 1.135,0.917 0.313,0.198 10 false *A 0.448,1.094 0.76,1.292 0.313,0.198 10 false V5 0.833,1.073 1.146,1.271 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Rain Sensor)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
V4-2 (ES) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
V5-2 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR