Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM33A0E _58 Vehicle Interior _065380 LIGHTING (INT) _0327154 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ON or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E380181E01
2.01,0.719 2.469,0.917 0.458,0.198 10 false ALT 0.677,0.521 1.719,0.833 1.042,0.313 10 false from Battery 0.146,1.115 1.969,1.667 1.823,0.552 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition Switch Assembly*2 0.469,2.688 2.896,2.927 2.427,0.24 10 false *1: w/ Smart Entry and Start System 0.469,3.042 2.896,3.281 2.427,0.24 10 false *2: w/o Smart Entry and Start System 3.115,2.698 4.167,2.917 1.052,0.219 10 false *3: for LHD 3.125,3.052 4.177,3.271 1.052,0.219 10 false *4: for RHD 2.771,0.542 3.229,0.74 0.458,0.198 10 false 3G 3.219,0.552 3.677,0.75 0.458,0.198 10 false 3F 3.25,0.344 3.708,0.542 0.458,0.198 10 false 1 2.833,0.344 3.292,0.542 0.458,0.198 10 false 1 2.792,0.771 3.073,1.01 0.281,0.24 10 false *4 3.219,0.771 3.5,1.01 0.281,0.24 10 false *3 3.229,1.167 3.688,1.365 0.458,0.198 10 false 3A 3.24,0.969 3.698,1.167 0.458,0.198 10 false 17 3.229,1.781 3.688,1.979 0.458,0.198 10 false 3B 3.271,1.583 3.729,1.781 0.458,0.198 10 false 3 5.885,2.615 6.344,2.813 0.458,0.198 10 false K51 4.063,1.448 4.854,1.656 0.792,0.208 10 false IG1-NO. 1 5.906,2.427 6.365,2.625 0.458,0.198 10 false 19 5.885,1.781 6.344,1.979 0.458,0.198 10 false MB 5.896,1.583 6.354,1.781 0.458,0.198 10 false 11 5.896,0.542 6.354,0.74 0.458,0.198 10 false MB 5.917,0.365 6.375,0.563 0.458,0.198 10 false 32 4.729,0.719 5.771,1.031 1.042,0.313 10 false ECU-IG1 NO. 4 6.292,0.427 6.75,0.625 0.458,0.198 10 false IG 6.313,1.781 6.771,1.979 0.458,0.198 10 false GND1 6.313,2.615 6.771,2.813 0.458,0.198 10 false GND2 3.156,2.198 5.958,2.438 2.802,0.24 10 false Instrument Panel Junction Block Assembly 5.385,3.052 7.021,3.417 1.635,0.365 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

First, check for smart entry and start system (for Start Function) DTCs, and after confirming that there is no malfunction, proceed with troubleshooting.*1

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*1: w/ Smart Entry and Start System

*2: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW Ignition switch ON signal OFF or ON OFF: Ignition switch off
ON: Ignition switch ON
"OFF" is also displayed for this item when the ignition switch is ACC.
Body Electrical > Main Body > Data List
Tester Display
IG SW
50003 123 30
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the 3F*1 or 3G*2 and 3B instrument panel junction block assembly connectors.


b.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground*1 Always 11 to 14 V
3G-1 - Body ground*2 Always 11 to 14 V


*1: for LHD

*2: for RHD



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-3 - Body ground Always Below 1 Ω
K51-19 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E333577C22
1.698,0.51 2.042,0.729 0.344,0.219 4.938,0.531 5.281,0.75 0.344,0.219 2.438,2.438 2.781,2.656 0.344,0.219 5.729,2.104 6.073,2.323 0.344,0.219 5.74,2.406 6.083,2.625 0.344,0.219 4.219,3.115 4.396,3.396 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 1.792,0.531 2.208,0.771 0.417,0.24 10 false 3B 5.031,0.552 5.448,0.792 0.417,0.24 10 false 3A 2.51,2.458 2.927,2.698 0.417,0.24 10 false MB 5.823,2.125 6.24,2.365 0.417,0.24 10 false 3F 4.458,3.385 4.875,3.625 0.417,0.24 10 false IG 5.813,2.417 6.229,2.656 0.417,0.24 10 false 3G 6.146,2.146 6.563,2.385 0.417,0.24 10 false *A 6.156,2.427 6.573,2.667 0.417,0.24 10 false *B
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3F-1 - MB-32 (IG) Battery not connected to 3A-17 and 3B-3 10 kΩ or higher
3F-1 - MB-32 (IG) Battery positive (+) → 3A-17
Battery negative (-) → 3B-3
Below 1 Ω


for RHD
Tester Connection Condition Specified Condition
3G-1 - MB-32 (IG) Battery not connected to 3A-17 and 3B-3 10 kΩ or higher
3G-1 - MB-32 (IG) Battery positive (+) → 3A-17
Battery negative (-) → 3B-3
Below 1 Ω


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY