Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM33A0E _58 Vehicle Interior _065380 LIGHTING (INT) _0327154 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Rear Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the rear door courtesy light switch assembly.

WIRING DIAGRAM

E344238E08
0.802,0.938 1.302,1.24 0.5,0.302 10 false R7 0.802,1.094 3.771,1.333 2.969,0.24 10 false Rear Door Courtesy Light Switch Assembly LH 0.844,2.156 1.344,2.458 0.5,0.302 10 false R6 0.833,2.333 3.865,2.792 3.031,0.458 10 false Rear Door Courtesy Light Switch Assembly RH 2.75,0.521 3.25,0.823 0.5,0.302 10 false 1 3.885,0.625 4.385,0.927 0.5,0.302 10 false 3D 3.896,0.427 4.396,0.729 0.5,0.302 10 false 24 3.896,1.615 4.396,1.917 0.5,0.302 10 false 31 3.885,1.802 4.385,2.104 0.5,0.302 10 false 3A 4.188,2.219 5.833,2.823 1.646,0.604 10 false Instrument Panel Junction Block Assembly 5.708,0.615 6.208,0.917 0.5,0.302 10 false MB 5.729,0.438 6.229,0.74 0.5,0.302 10 false 13 5.75,1.615 6.25,1.917 0.5,0.302 10 false 2 6.094,0.5 6.594,0.802 0.5,0.302 10 false LCTY 6.458,0.24 6.958,0.542 0.5,0.302 10 false +B 5.271,2.802 6.948,3.51 1.677,0.708 10 false Main Body ECU (Multiplex Network Body ECU) 2.771,1.729 3.271,2.031 0.5,0.302 10 false 1 5.698,1.813 6.198,2.115 0.5,0.302 10 false MB 6.094,1.635 6.594,1.938 0.5,0.302 10 false RCTY 6.469,1.417 6.969,1.719 0.5,0.302 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*1: w/ Smart Entry and Start System

*2: w/ Door Control Battery




PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch assembly RH signal OFF or ON OFF: Rear door RH closed
ON: Rear door RH open
-
RL Door Courtesy SW Rear door courtesy light switch assembly LH signal OFF or ON OFF: Rear door LH closed
ON: Rear door LH open
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25
OK:

Normal conditions listed above are displayed.



Result:
Result Proceed to
OK A
NG ("RR Door Courtesy SW" is not normal) B
NG ("RL Door Courtesy SW" is not normal) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

C

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
2.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

3.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R6-1 - 3A-31 Always Below 1 Ω
R6-1 or 3A-31 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E365380C01
1.24,0.198 1.563,0.438 0.323,0.24 4.792,0.375 5.115,0.615 0.323,0.24 3.375,1.344 3.396,1.063 false 0.198,0.146 0.51,0.344 0.313,0.198 10 false *a 1.302,0.229 1.688,0.469 0.385,0.24 10 false 3A 4.833,0.406 5.229,0.635 0.396,0.229 10 false MB 3.219,1.354 3.729,1.594 0.51,0.24 10 false RCTY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-31 - MB-2 (RCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Remove the rear door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R7-1 - 3D-24 Always Below 1 Ω
R7-1 or 3D-24 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E370559C01
4.75,0.438 5.083,0.698 0.333,0.26 1.208,0.229 1.542,0.49 0.333,0.26 4.49,1.417 4.667,1.063 false 0.208,0.156 0.521,0.354 0.313,0.198 10 false *a 4.792,0.469 5.104,0.667 0.313,0.198 10 false MB 1.281,0.26 1.594,0.458 0.313,0.198 10 false 3D 4.323,1.438 4.844,1.635 0.521,0.198 10 false LCTY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-24 - MB-13 (LCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY