Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1246  Master Cylinder Pressure Sensor Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

C106656E65
3.927,4.115 5.552,4.313 1.625,0.198 10 false Brake Actuator Assembly 2.896,1.344 4.042,1.531 1.146,0.188 10 false Skid Control ECU 5.406,2.583 6.5,2.938 1.094,0.354 10 false Master Cylinder Pressure Sensor 0.563,1.958 1.438,2.208 0.875,0.25 10 false from Battery 0.26,2.625 1.344,2.969 1.083,0.344 10 false from Stop Light Switch Assembly 0.354,3.375 1.396,3.604 1.042,0.229 10 false to Body Ground 2.76,1.979 3.073,2.177 0.313,0.198 10 false +BS 2.76,2.688 3.177,2.885 0.417,0.198 10 false STP 2.76,3.396 3.135,3.594 0.375,0.198 10 false GND 3.865,1.979 4.333,2.188 0.469,0.208 10 false VCM 3.865,2.677 4.313,2.885 0.448,0.208 10 false PMC 3.99,3.385 4.302,3.604 0.313,0.219 10 false E2 0.542,4.76 3.958,4.969 3.417,0.208 10 false VCM: Master Cylinder Pressure Sensor Power Supply 0.542,5.01 3.427,5.219 2.885,0.208 10 false PMC: Master Cylinder Pressure Sensor Input 0.542,5.26 3.427,5.479 2.885,0.219 10 false E2: Master Cylinder Pressure Sensor Ground

DTC No. Detection Item DTC Detection Condition Trouble Area
C1246 Master Cylinder Pressure Sensor Malfunction Any of the following is detected:
1.

The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V).

2.

An abnormality is detected in the skid control ECU internal sensor test.

3.

The sensor signal offset value is out of range.


·

Stop light switch assembly circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder pressure sensor (brake actuator assembly)



DTC Detection Conditions: C1246
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V). ○ - -
An abnormality is detected in the skid control ECU internal sensor test. - ○ -
The sensor signal offset value is out of range. - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.READ VALUE USING GTS (BS1 VOLTAGE VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BS1 Voltage Value +BS voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
Chassis > ABS/VSC/TRC > Data List
Tester Display
BS1 Voltage Value
50003 105 273

d.

Take a note of the +BS voltage value.

HINT:

The noted +BS voltage value is used in a later step.



Result:
Proceed to
NEXT



NEXT

2.CHECK STOP LIGHT OPERATION
2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

3.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays on or off according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

NG

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
4.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

Start the engine.


b.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Sensor Master cylinder pressure sensor reading Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.20 to 0.40 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Master Cylinder Sensor
50003 105 9

c.

Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.

OK:

When the brake pedal is depressed, the voltage displayed on the GTS increases.



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

5.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
C1246 is not output A
C1246 is output B



A

B

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C360727C71
0.271,0.281 0.719,0.531 0.448,0.25 2.563,0.365 2.208,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.365,0.323 0.708,0.542 0.344,0.219 10 false A34 2.479,0.188 2.906,0.375 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)