Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C146C  Open in ABS Motor Relay Circuit  


DESCRIPTION

The ABS motor relay supplies power to the pump motor. While the ABS is activated, the skid control ECU (brake actuator assembly) turns the ABS motor relay on to operate the pump motor.

If the voltage supplied to the ABS motor relay (+BM) is too low due to low voltage from the battery or alternator, this DTC may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146C Open in ABS Motor Relay Circuit Any of the following is detected:
1.

When the ABS motor relay is actuated, voltage is not supplied to the pump motor.

2.

When the ABS motor relay is not actuated, voltage in the pump motor is high.

3.

The skid control ECU (brake actuator assembly) judges that pump motor operation is abnormal.


·

ABS NO. 1 fuse

·

ABS motor relay circuit

·

ABS motor relay (brake actuator assembly)



DTC Detection Conditions: C146C
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition The ABS motor relay is actuated. ○ - -
The ABS motor relay is not actuated. - ○ -
Malfunction Status Voltage is not supplied to the pump motor. ○ - -
Voltage in the pump motor is high. - ○ -
The skid control ECU (brake actuator assembly) judges that pump motor operation is abnormal. - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C377579E03
0.854,4.083 1.927,4.281 1.073,0.198 10 false Battery 0.771,3.073 1.844,3.271 1.073,0.198 10 false FL MAIN 3.792,1.542 4.25,1.74 0.458,0.198 10 false +BM 1.865,1.573 3.01,1.833 1.146,0.26 10 false ABS NO. 1 3.802,3.51 4.417,3.708 0.615,0.198 10 false GND2 4.896,1.406 6.844,1.75 1.948,0.344 10 false ABS Motor Relay 4.854,2.208 6.552,2.615 1.698,0.406 10 false Skid Control ECU 5.281,4.719 6.813,4.917 1.531,0.198 10 false Pump Motor 4.76,5.146 5.219,5.344 0.458,0.198 10 false A34 4.75,5.302 6.844,5.656 2.094,0.354 10 false Brake Actuator Assembly 1.948,1.292 2.104,1.49 0.156,0.198 10 false 1 2.417,1.292 2.573,1.49 0.156,0.198 10 false 2 3.594,1.302 3.75,1.5 0.156,0.198 10 false 1 3.542,3.25 3.771,3.479 0.229,0.229 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When C1241 and/or C1417 is output together with C146C, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

for C1241: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241

for C1417: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1417


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay ABS motor relay Relay OFF/ON Operating sound of motor can be heard
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Motor Relay
50004 105 2

d.

Check the operating sound of the pump motor when operating it using the GTS.


Result:
Result Proceed to
Operating sound is heard A
Operating sound is not heard B



A

2.RECONFIRM DTC

B

3.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
2.RECONFIRM DTC
HINT:

This DTC is stored when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay is in the skid control ECU (brake actuator assembly).

Therefore, ABS motor relay inspection and ABS motor relay unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the skid control ECU (brake actuator assembly).


a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for 30 seconds or more.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
C146C is not output A
C146C is output B


HINT:
·

If a speed signal of 40 km/h (25 mph) or more is received by the skid control ECU (brake actuator assembly) with the ignition switch to ON, the skid control ECU (brake actuator assembly) performs self diagnosis of the motor circuit.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B

3.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
a.
C360727C75
0.385,0.26 0.792,0.521 0.406,0.26 1.063,1.854 0.667,1.229 true 0.969,1.885 1.615,2.083 0.646,0.198 10 false +BM 0.104,0.063 0.365,0.24 0.26,0.177 10 false *a 0.458,0.302 0.844,0.479 0.385,0.177 10 false A34
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-1 (+BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C360727C76
0.292,0.271 0.74,0.542 0.448,0.271 2.438,1.771 2.75,1.24 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 0.385,0.323 0.771,0.521 0.385,0.198 10 false A34 2.229,1.813 2.74,1.979 0.51,0.167 10 false GND2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-14 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)