Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1434  Steering Angle Sensor Output Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the steering angle sensor via CAN communication.

HINT:

If there is a malfunction in the bus lines between the steering angle sensor and the CAN communication system, DTC U0126 (Lost Communication with Steering Angle Sensor Module) is output. When U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0126 first.


DTCs may be stored if one of the following occurs:

·

Steering angle sensor zero point value malfunction.

·

Steering angle sensor signal malfunction.

·

Steering angle sensor signal stuck malfunction.

·

Steering angle sensor and the yaw rate sensor values inconsistent.

·

Steering angle sensor installation abnormality.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1434 Steering Angle Sensor Output Malfunction Any of the following is detected:
1.

The difference between the zero point of the steering angle sensor and the estimated zero point exceeds 15 deg.

2.

The offset value of the steering angle sensor is -13.5 deg. or less or 13.5 deg. or more.

3.

The steering angle sensor value exceeds a specified value for 0.3 seconds or more.

4.

The change of the steering angle sensor value within 0.02 seconds is abnormal.

5.

The steering angle sensor value changes by less than 5 deg. and both left and right turns have been recognized.

6.

There is a difference between the skid control ECU (brake actuator assembly) estimated value and the steering angle sensor value due to an abnormal steering angle sensor value.


·

Steering angle sensor installation

·

Steering angle sensor power supply

·

Steering angle sensor

·

Skid control ECU (brake actuator assembly)



DTC Detection Conditions: C1434
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition The steering angle sensor value changes by less than 5 deg. - - - - ○ -
Malfunction Status The difference between the zero point of the steering angle sensor and the estimated zero point exceeds 15 deg. ○ - - - - -
The offset value of the steering angle sensor is -13.5 deg. or less or 13.5 deg. or more. - ○ - - - -
The steering angle sensor value exceeds a specified value. - - ○ - - -
The change of the steering angle sensor value within 0.02 seconds is abnormal. - - - ○ - -
Both left and right turns have been recognized. - - - - ○ -
There is a difference between the skid control ECU (brake actuator assembly) estimated value and the steering angle sensor value due to an abnormal steering angle sensor value. - - - - - ○
Detection Time - - 0.3 seconds or more - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

When U0073, U0123 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0123 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073

·

When a speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal. When DTCs for a speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


d.

Start the engine.


e.

Drive the vehicle at a speed of 50 km/h (31 mph) and turn the steering wheel to the right and left and then check that no speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
No CAN communication system, speed sensor, or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output A
CAN communication system DTCs are output B
Speed sensor and/or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output C


HINT:
·

If a speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair these malfunctions and then inspect the steering angle sensor.





A

2.CHECK STEERING ANGLE SENSOR INSTALLATION

B

C

2.CHECK STEERING ANGLE SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the steering angle sensor has been installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>INSTALLATION

OK:

The steering angle sensor installation is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C374262C07
0.229,0.771 0.615,1.01 0.385,0.24 2,1.99 2.604,1.635 true 2,2.375 2.604,2.823 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 0.313,0.813 0.771,1.01 0.458,0.198 10 false K71 2.667,2.76 3.125,2.958 0.458,0.198 10 false IG1 2.667,1.552 3.125,1.75 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor)


Remove the steering wheel and column cover.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the K71 steering angle sensor connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K71-4 (BAT) - Body ground Always 11 to 14 V
K71-9 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C374262C08
0.229,0.771 0.615,1.01 0.385,0.24 1.323,2.385 0.76,2.823 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 0.313,0.813 0.771,1.01 0.458,0.198 10 false K71 0.448,2.781 0.906,2.979 0.458,0.198 10 false ESS
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Before measuring the resistance of the steering angle sensor, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.


Standard Resistance:
Tester Connection Condition Specified Condition
K71-6 (ESS) - Body ground 1 minute after ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)