Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TRC does not Operate  


DESCRIPTION

When TRC or VSC is operating, the skid control ECU (brake actuator assembly) blinks the slip indicator light to inform the driver that slippage occurred.

When in VSC off mode, or TRC and VSC are disabled, the multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates to inform the driver.

When a communication malfunction with the ECM is detected, TRC and VSC are disabled. Also when the system is malfunctioning, TRC and VSC are disabled and the indicator lights of related systems illuminate.

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.BRAKE PROBLEM CHECK
a.

Check if the slip indicator light was illuminated when TRC did not operate.

OK:

The slip indicator light was illuminated.


HINT:

When a DTC is stored, the slip indicator light is illuminated and TRC does not operate due to the fail-safe function.



b.

Check the operation condition of the VSC OFF switch when TRC did not operate.

OK:

The VSC OFF switch had been operated to turn off TRC when TRC did not operate.


HINT:

When the multi-information display in the combination meter assembly displays "Traction Control Turned Off", TRC does not operate.



Result:
Proceed to
OK
NG



OK

END

NG

2.CHECK DTC
2.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check the DTCs (vehicle stability control system) that are output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs are not output A
Vehicle stability control system DTCs are output B



A

3.CHECK VEHICLE

B

3.CHECK VEHICLE
a.

Operate the VSC OFF switch and check that the multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates in accordance with the operation of the switch.

OK:

The multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates in accordance with the operation of the switch.



Result:
Proceed to
OK
NG



OK

4.PERFORM TEST MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CIRCUIT)

NG

4.PERFORM TEST MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CIRCUIT)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.


b.

Using the GTS, perform a Test Mode (Signal Check) inspection sensor check and check that speed sensor Test Mode (Signal Check) inspection items change from incomplete to complete.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 4359
OK:

Speed sensor Test Mode (Signal Check) inspection items change from incomplete to complete.



Result:
Proceed to
OK
NG



OK

5.PERFORM OPERATION CHECK DRIVING

NG

INSPECT AND REPAIR MALFUNCTIONING SPEED SENSOR CIRCUIT

5.PERFORM OPERATION CHECK DRIVING
a.

Operate the VSC OFF switch and check that the system is not in TRC off mode or VSC off mode.


b.

Check that no DTCs are output and that each warning light is not illuminated.


c.

Start off the vehicle on a low friction surface and check that TRC operates when attempting to make the drive wheels slip.

OK:

TRC operates when slip occurs when starting off.


NOTICE:
·

Even when the system is normal, VSC may not operate when the vehicle speed is low or TRC may not operate due to a malfunction. Make sure that only the drive wheels slip during the procedure.

·

When confirming that the slip indicator light blinks, do not slip the drive wheels longer than necessary. Whether TRC operated or not can be checked by reading the Freeze Frame Data when the system operated.

·

Pay attention to your surroundings when performing the procedure and depress the accelerator pedal with caution.




Result:
Proceed to
OK
NG



OK

NG