Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS
RM33A0E _59 Vehicle Exterior _065390 WINDOW / GLASS _0327256 BACK WINDOW GLASS A

WINDOW / GLASS  BACK WINDOW GLASS  INSTALLATION  


PROCEDURE

Hide 56115B 1.INSTALL NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)

a.
B485036

Install 2 new No. 1 back window glass stoppers to the vehicle body as shown in the illustration.

HINT:

Only 2-piece type back window glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56116D 2.INSTALL NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the installation area of 2 new No. 2 back window glass stoppers with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.
B470003C01
0.823,0.854 1.26,0.552 false 1.375,1 2.073,0.542 2.073,0.542 1.906,0.979 false 1.635,0.979 2.083,0.542 false 0.073,0.073 0.417,0.302 0.344,0.229 12 false *A 2.125,0.448 2.438,0.604 0.313,0.156 10 false *a 1.292,0.49 1.604,0.646 0.313,0.156 10 false *b 2.74,0.76 2.896,0.958 0.156,0.198 10 false a
*A Back Side
*a Ceramic Notch
*b Back Window Glass Edge Side


Install the 2 new No. 2 back window glass stoppers to the back window glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 14.7 mm (0.579 in.)


HINT:

Only 2-piece type back window glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 64813D 3.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut 2 new back window glass adhesive dams so that they are the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 130 to 140 mm (5.12 to 5.51 in.)



b.

Using a brush or sponge, coat the installation area of the 2 new back window glass adhesive dams with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



c.

Install the 2 back window glass adhesive dams to the back window glass as shown in the illustration.

B470000C01
2.125,1.125 1.76,1.292 1.76,1.292 2.052,1.021 false 3.865,1.167 4.229,1.313 4.229,1.313 3.896,1.042 false 5.615,2.479 5.219,1.938 false 0.115,0.104 0.427,0.323 0.313,0.219 12 false *A 1.677,1.302 1.958,1.458 0.281,0.156 10 true *a 5.667,2.417 5.979,2.573 0.313,0.156 10 false *b 4.156,1.313 4.469,1.469 0.313,0.156 10 false *a 2.031,0.5 2.188,0.698 0.156,0.198 10 false a 3.719,0.531 3.875,0.729 0.156,0.198 10 false b 2.823,1.552 2.979,1.75 0.156,0.198 10 false A 2.969,2.302 3.125,2.5 0.156,0.198 10 false A 5,1.281 5.458,1.479 0.458,0.198 10 false A-A
*A Back Side - -
*a Ceramic Notch *b Back Window Glass Adhesive Dam Positioning Center


Standard Dimension:
Area Dimension
a 0 to 10.0 mm (0 to 0.394 in.)
b 0 to 10.0 mm (0 to 0.394 in.)



d.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut a new back window glass adhesive dam so that it is the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 56.8 to 57.8 cm (1.86 to 1.90 ft.)



e.

Using a brush or sponge, coat the installation area of the new back window glass adhesive dam with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



f.

Install the back window glass adhesive dam to the back window glass as shown in the illustration.

B470001C01
1.448,1.198 0.948,1.271 0.948,1.271 1.354,1.052 false 3.229,1.219 3.615,1.292 3.615,1.292 3.323,1.052 false 5.719,2.458 5.219,1.948 false 0.083,0.094 0.458,0.375 0.375,0.281 12 false *A 3.656,1.229 3.823,1.396 0.167,0.167 10 true *a 5.76,2.406 6.073,2.563 0.313,0.156 10 false *b 0.781,1.198 0.948,1.365 0.167,0.167 10 true *a 1.406,0.594 1.563,0.792 0.156,0.198 10 false a 3.219,0.604 3.375,0.802 0.156,0.198 10 false b 4.99,1.229 5.417,1.458 0.427,0.229 10 false A-A 2,1.802 2.156,2 0.156,0.198 10 false A 2,2.125 2.156,2.323 0.156,0.198 10 false A
*A Back Side - -
*a Ceramic Notch *b Back Window Glass Adhesive Dam Positioning Center


Standard Dimension:
Area Dimension
a 0 to 10.0 mm (0 to 0.394 in.)
b 0 to 10.0 mm (0 to 0.394 in.)



g.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut 2 new back window glass adhesive dams so that they are the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 62.5 to 63.5 cm (2.05 to 2.08 ft.)



h.

Using a brush or sponge, coat the installation area of the 2 new back window glass adhesive dams with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



i.

Install the 2 back window glass adhesive dams to the back window glass as shown in the illustration.

B469999C01
5.573,1.813 6.073,2.24 false 2.385,0.792 2.792,0.552 false 2.365,2.99 2.906,3.188 false 0.125,0.115 0.5,0.354 0.375,0.24 12 false *A 2.219,0.729 2.531,0.885 0.313,0.156 10 false *a 6.125,2.188 6.438,2.344 0.313,0.156 10 false *b 2.198,2.896 2.51,3.052 0.313,0.156 10 false *a 4.708,1.25 5.021,1.458 0.313,0.208 10 false A-A 3.104,1.448 3.26,1.646 0.156,0.198 10 false A 3.417,1.458 3.573,1.656 0.156,0.198 10 false A 3.208,0.354 3.365,0.552 0.156,0.198 10 false a 3.323,3.146 3.479,3.344 0.156,0.198 10 false b
*A Back Side - -
*a Ceramic Notch *b Back Window Glass Adhesive Dam Positioning Center


Standard Dimension:
Area Dimension
a 0 to 10.0 mm (0 to 0.394 in.)
b 0 to 10.0 mm (0 to 0.394 in.)



j.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut a new back window glass adhesive dam so that it is the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 117.8 to 118.8 cm (3.86 to 3.90 ft.)



k.

Using a brush or sponge, coat the installation area of the new back window glass adhesive dam with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



l.

Install the back window glass adhesive dam to the back window glass as shown in the illustration.

B470002C01
5.229,1.948 5.698,2.396 false 1.292,2.906 1.021,2.708 1.021,2.708 1.417,2.813 false 3.573,2.938 3.865,2.771 3.865,2.771 3.458,2.854 false 0.125,0.115 0.469,0.333 0.344,0.219 12 false *A 0.865,2.615 1.177,2.771 0.313,0.156 10 false *a 5.76,2.333 6.073,2.49 0.313,0.156 10 false *b 3.917,2.677 4.073,2.833 0.156,0.156 10 true *a 2.667,1.646 2.823,1.844 0.156,0.198 10 false A 2.667,1.969 2.823,2.167 0.156,0.198 10 false A 4.99,1.229 5.448,1.427 0.458,0.198 10 false A-A 1.26,3.271 1.417,3.469 0.156,0.198 10 false a 3.552,3.292 3.708,3.49 0.156,0.198 10 false b
*A Back Side - -
*a Ceramic Notch *b Back Window Glass Adhesive Dam Positioning Center


Standard Dimension:
Area Dimension
a 0 to 10.0 mm (0 to 0.394 in.)
b 0 to 10.0 mm (0 to 0.394 in.)



Hide 4.INSTALL BACK WINDOW GLASS SUB-ASSEMBLY

a.
B469646C01
1.656,0.969 1.375,0.969 1.375,0.969 1.375,1.49 true 1.385,1.26 1.646,1.26 true 1.323,1.51 1.51,1.677 0.188,0.167 10 true *a
*a Matchmark


Position the back window glass sub-assembly.

i.

Using suction cups, place the back window glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the back window glass sub-assembly rim is perfectly even.


iii.

Align the matchmarks on the back window glass sub-assembly and vehicle body.

NOTICE:

Check that the back window glass stoppers are engaged to the vehicle body correctly.



iv.

Remove the back window glass sub-assembly.



b.

Using a brush, coat the installation surface on the vehicle body with body primer.

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the adhesive application area with glass primer.

B470004C01
3.688,1.469 3.99,1.469 false 3.646,2.063 3.948,2.063 false 0.104,0.135 0.469,0.427 0.365,0.292 12 false *A 4.021,1.406 4.333,1.563 0.313,0.156 10 false *a 3.99,2 4.302,2.156 0.313,0.156 10 false *b 1.219,0.448 1.375,0.646 0.156,0.198 10 false A 1.198,0.76 1.302,0.927 0.104,0.167 10 true A 2.594,0.5 2.75,0.698 0.156,0.198 10 false B 2.594,0.813 2.75,1.01 0.156,0.198 10 false B 0.771,0.896 0.927,1.094 0.156,0.198 10 false C 1.073,0.906 1.229,1.104 0.156,0.198 10 false C 1.094,1.865 1.219,2.031 0.125,0.167 10 true D 1.083,2.188 1.24,2.385 0.156,0.198 10 false D 0.865,2.625 1.323,2.823 0.458,0.198 10 false A-A 2.875,2.542 3.333,2.74 0.458,0.198 10 false B-B 5.073,2.24 5.531,2.438 0.458,0.198 10 false D-D 5.167,0.552 5.625,0.75 0.458,0.198 10 false C-C 1.583,2.667 1.74,2.865 0.156,0.198 10 false a 3.229,2.667 3.385,2.865 0.156,0.198 10 false b 5.542,0.667 5.698,0.865 0.156,0.198 10 false c 5.594,2.333 5.75,2.531 0.156,0.198 10 false d
*A Back Side - -
*a Adhesive center position *b Ceramic Notch
V100155

Glass Primer - -


Standard Dimension:
Area Dimension
a 11.0 mm (0.433 in.) or more
b 11.0 mm (0.433 in.) or more
c 11.0 mm (0.433 in.) or more
d 19.0 mm (0.748 in.) or more


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:
·

Apply glass primer onto the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.




d.

Apply adhesive to the back window glass sub-assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus Type) or Equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 to 15.0 mm (0.472 to 0.591 in.)
b 8.0 to 11.0 mm (0.315 to 0.433 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back window glass sub-assembly as shown in the illustration.

B470005C01
3.677,1.708 3.969,1.708 false 3.646,2.063 3.938,2.063 false 0.125,0.125 0.479,0.417 0.354,0.292 12 false *A 4,1.635 4.313,1.792 0.313,0.156 10 false *a 3.969,2 4.281,2.156 0.313,0.156 10 false *b 1.188,0.438 1.344,0.635 0.156,0.198 10 false A 1.188,0.75 1.292,0.938 0.104,0.188 10 true A 2.594,0.802 2.75,1 0.156,0.198 10 true B 2.583,0.49 2.74,0.688 0.156,0.198 10 false B 0.771,0.885 0.927,1.083 0.156,0.198 10 false C 1.094,0.906 1.25,1.104 0.156,0.198 10 false C 1.083,1.875 1.188,2.052 0.104,0.177 10 true D 1.073,2.188 1.177,2.365 0.104,0.177 10 true D 0.854,2.49 1.313,2.688 0.458,0.198 10 false A-A 2.854,2.302 3.313,2.5 0.458,0.198 10 false B-B 5.021,2 5.479,2.198 0.458,0.198 10 false D-D 5.167,0.365 5.625,0.563 0.458,0.198 10 false C-C 5.25,2.156 5.406,2.354 0.156,0.198 10 false d 1.698,2.5 1.854,2.698 0.156,0.198 10 false a 3.021,2.5 3.177,2.698 0.156,0.198 10 false b 5.333,0.51 5.49,0.708 0.156,0.198 10 false c 5.563,2.167 5.719,2.365 0.156,0.198 10 false e
*A Back Side - -
*a Adhesive Positioning Center *b Ceramic Notch
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 8.5 to 11.5 mm (0.335 to 0.453 in.)
b 13.3 mm (0.524 in.)
c 13.2 mm (0.520 in.)
d 16.4 mm (0.646 in.)
e 8.0 to 11.0 mm (0.315 to 0.433 in.)


HINT:

Apply adhesive to the ceramic notches.




e.

Install the back window glass sub-assembly.

i.
B469646C01
1.656,0.969 1.375,0.969 1.375,0.969 1.375,1.49 true 1.385,1.26 1.646,1.26 true 1.323,1.51 1.51,1.677 0.188,0.167 10 true *a
*a Matchmark


Using suction cups, position the back window glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the back window glass stoppers are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and back window glass sub-assembly.




ii.

Lightly press the outer surface of the back window glass sub-assembly to ensure that the back window glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the back window glass sub-assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




f.

Connect each connector.


Hide 5.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 64340B 6.INSTALL NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

Hide 64330 7.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)

Hide 64330 8.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

Hide 73373F 9.INSTALL REAR SEAT SHOULDER BELT HOLE COVER

Hide 73370E 11.CONNECT REAR SEAT OUTER BELT ASSEMBLY LH

Hide 73360D 12.CONNECT REAR SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 13.INSTALL ROOF HEADLINING ASSEMBLY