Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327338 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660  P Seat Airbag Active Mode Indicator  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator (telltale light assembly).

The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger airbag assembly and lower No. 2 instrument panel airbag assembly.

DTC B1660 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1660 P Seat Airbag Active Mode Indicator
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the passenger airbag ON/OFF indicator circuit.

·

Passenger airbag ON/OFF indicator malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Instrument panel junction block assembly

·

Passenger airbag ON/OFF indicator (Telltale light assembly)

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B474761E03
3.458,1.49 3.823,1.75 0.365,0.26 10 false 3A 3.458,1.656 4.542,2.354 1.083,0.698 10 false Instrument Panel Junction Block Assembly 5.188,0.469 5.552,0.729 0.365,0.26 10 false 35 5.188,1.156 5.552,1.417 0.365,0.26 10 false 34 5.188,2.313 5.552,2.573 0.365,0.26 10 false 33 5.188,2.625 5.552,2.885 0.365,0.26 10 false 32 5.417,2.625 5.781,2.885 0.365,0.26 10 false E2 5.417,2.313 5.781,2.573 0.365,0.26 10 false E1 5.375,3.313 7.031,3.656 1.656,0.344 10 false Airbag Sensor Assembly 5.375,3.146 7.031,3.49 1.656,0.344 10 false K73 5.427,0.469 6.01,0.729 0.583,0.26 10 false PAON 5.427,1.167 6.01,1.427 0.583,0.26 10 false P-AB 4.771,0.469 5.135,0.729 0.365,0.26 10 false 8 4.771,1.156 5.208,1.417 0.438,0.26 10 false 46 3.26,1.156 3.698,1.417 0.438,0.26 10 false 51 3.26,0.469 3.625,0.729 0.365,0.26 10 false 29 2.365,0.563 2.948,0.823 0.583,0.26 10 false PAON 2.438,1.26 3.021,1.521 0.583,0.26 10 false P-AB 2.844,0.469 3.208,0.729 0.365,0.26 10 false 5 2.844,1.156 3.208,1.417 0.365,0.26 10 false 4 2.073,1.646 2.438,1.906 0.365,0.26 10 false K36 2.073,1.823 3.198,2.865 1.125,1.042 10 false Passenger Airbag ON/OFF Indicator (Telltale Light Assembly) 0.677,1.031 1.927,1.313 1.25,0.281 10 false ECU-IG1 NO. 4 2.115,0.885 3.365,1.167 1.25,0.281 10 false IG+ 0.135,0.219 1.656,0.646 1.521,0.427 10 false from IG1-NO. 1 Relay 1.865,0.771 3.115,1.052 1.25,0.281 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the ignition switch to ON.


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>OPERATION CHECK



Result:
Result Proceed to
Passenger airbag ON/OFF indicator illumination is always on. A
Passenger airbag ON/OFF indicator illumination is always off. B



A

2.CHECK CONNECTION OF CONNECTORS

B

8.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, telltale light assembly and instrument panel junction block assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, telltale light assembly and instrument panel junction block assembly.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Connect the connector to the telltale light assembly and instrument panel junction block assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

6.CHECK WIRE HARNESS
5.CHECK DTC
a.
C284134C01
0.271,0.802 0.583,1.073 0.313,0.271 10 false *1 2.906,0.813 3.219,1.104 0.313,0.292 10 false *2 0.292,1.469 0.719,1.917 0.427,0.448 10 false *3 2.615,0.802 2.927,1.146 0.313,0.344 10 false A 2.427,0.802 2.74,1.198 0.313,0.396 10 false B 0.74,0.802 1.042,1.177 0.302,0.375 10 false C 0.552,0.802 0.865,1.094 0.313,0.292 10 false D 0.729,1.479 1.083,1.979 0.354,0.5 10 false E 0.563,1.479 0.875,1.635 0.313,0.156 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Telltale Light Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Connect the connector to the airbag sensor assembly.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK WIRE HARNESS
a.
B474762C01
0.75,0.51 1.115,0.75 0.365,0.24 0.802,3.917 1.167,4.156 0.365,0.24 1.896,3.292 1.896,2.542 false 1.635,2.896 1.885,2.896 false 2.531,1.698 2.198,1.698 false 2.5,1.01 2.115,1.354 false 1.167,1.01 2.01,1.344 false 1.49,4.396 1.74,4.094 false 2.115,4.396 1.875,4.094 false 0.188,2.469 0.542,2.802 0.354,0.333 10 false *1 3.021,2.479 3.406,2.802 0.385,0.323 10 false *2 1.823,3.302 2.177,3.51 0.354,0.208 10 false *4 2.552,1.615 2.906,1.885 0.354,0.271 10 false *5 0.531,0.135 0.958,0.552 0.427,0.417 10 false *a 0.594,3.729 1,4.083 0.406,0.354 10 false *b 0.188,3.146 0.542,3.479 0.354,0.333 10 false *3 2.698,2.479 3.083,2.802 0.385,0.323 10 false A 2.313,2.479 2.698,2.802 0.385,0.323 10 false B 0.625,2.479 1.01,2.802 0.385,0.323 10 false C 0.448,2.479 0.833,2.802 0.385,0.323 10 false D 0.823,3.156 1.208,3.479 0.385,0.323 10 false E 0.448,3.156 0.833,3.479 0.385,0.323 10 false F 0.813,0.542 1.167,0.844 0.354,0.302 10 false K73 2.531,0.938 3.01,1.208 0.479,0.271 10 false PAON 0.802,0.938 1.281,1.208 0.479,0.271 10 false P-AB 0.865,3.958 1.219,4.26 0.354,0.302 10 false K36 1.958,4.396 2.438,4.667 0.479,0.271 10 false PAON 1.302,4.396 1.781,4.667 0.479,0.271 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Telltale Light Assembly
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Telltale Light Assembly)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the connector from the telltale light assembly.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K36-5 (PAON) - Body ground Ignition switch ON Below 1 V
K36-4 (P-AB) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-5 (PAON) - K36-4 (P-AB) Always Below 1 Ω



k.

Disconnect the service wire from connector B.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-5 (PAON) - K36-4 (P-AB) Always 1 MΩ or higher
K36-5 (PAON) - Body ground Always 1 MΩ or higher
K36-4 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

7.CHECK INSTRUMENT PANEL WIRE
7.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the connector from the instrument panel junction block assembly.

B477424C01
3.375,0.094 3.708,0.292 0.333,0.198 4.094,2.75 4.427,2.948 0.333,0.198 1.313,3.042 1.646,3.24 0.333,0.198 3.667,2.427 3.667,1.76 false 3.469,2 3.667,2 false 2.906,1.125 3.719,0.604 false 3.417,1.135 3.656,0.833 false 4.031,1.125 4.177,0.719 false 4.552,1.135 4.271,0.833 false 5.302,3.646 5.635,3.646 false 5.24,3.396 5.521,3.156 false 5.167,3.396 4.49,3.156 false 2.156,3.573 2.156,3.427 false 2.104,3.188 1.76,3.458 false 2.208,3.188 2.542,3.458 false 2.292,1.688 2.677,2.021 0.385,0.333 10 false *1 2.292,2.146 2.708,2.51 0.417,0.365 10 false *3 4.573,1.698 5,2.156 0.427,0.458 10 false *2 3.604,2.448 3.99,2.802 0.385,0.354 10 false *4 2.292,0.083 2.719,0.51 0.427,0.427 10 false *a 4.344,1.688 4.771,2.146 0.427,0.458 10 false A 4.031,1.688 4.458,2.146 0.427,0.458 10 false B 2.813,1.688 3.24,2.146 0.427,0.458 10 false C 2.51,1.688 2.938,2.146 0.427,0.458 10 false D 2.813,2.135 3.24,2.594 0.427,0.458 10 false E 2.51,2.135 2.938,2.594 0.427,0.458 10 false F 3.969,2.438 4.396,2.865 0.427,0.427 10 false *b 1.26,2.823 1.688,3.25 0.427,0.427 10 false *c 3.458,0.115 3.844,0.469 0.385,0.354 10 false 3A 2.708,1.135 3.198,1.458 0.49,0.323 10 false PAON 3.24,1.135 3.729,1.458 0.49,0.323 10 false P-AB 3.844,1.135 4.333,1.458 0.49,0.323 10 false PAON 4.438,1.135 4.927,1.458 0.49,0.323 10 false P-AB 4.146,2.771 4.542,3.042 0.396,0.271 10 false K73 5.667,3.573 5.958,3.771 0.292,0.198 10 false *5 4.146,3.073 4.635,3.396 0.49,0.323 10 false P-AB 5.542,3.073 6.031,3.396 0.49,0.323 10 false PAON 2.094,3.583 2.396,3.792 0.302,0.208 10 false *5 1.583,3.458 2.073,3.781 0.49,0.323 10 false P-AB 2.385,3.458 2.875,3.781 0.49,0.323 10 false PAON 1.365,3.063 1.76,3.333 0.396,0.271 10 false K36
*1 Instrument Panel Junction Block Assembly *2 Airbag Sensor Assembly
*3 Telltale Light Assembly *4 Instrument Panel Wire
*5 Service Wire - -
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)
*c Front view of wire harness connector
(to Telltale Light Assembly)
- -



b.

Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


e.

Using a service wire, connect terminals 5 (PAON) and 4 (P-AB) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-29 (PAON) - 3A-51 (P-AB) Always Below 1 Ω



g.

Disconnect the service wire from connector E.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground or other terminals Always 1 MΩ or higher
3A-29 (PAON) - Body ground or other terminals Always 1 MΩ or higher
3A-46 (P-AB) - Body ground or other terminals Always 1 MΩ or higher
3A-51 (P-AB) - Body ground or other terminals Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, telltale light assembly and instrument panel junction block assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

9.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

9.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, telltale light assembly and instrument panel junction block assembly.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

10.CHECK WIRE HARNESS

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK WIRE HARNESS
a.
B474762C01
0.75,0.51 1.115,0.75 0.365,0.24 0.802,3.917 1.167,4.156 0.365,0.24 1.896,3.292 1.896,2.542 false 1.635,2.896 1.885,2.896 false 2.531,1.698 2.198,1.698 false 2.5,1.01 2.115,1.354 false 1.167,1.01 2.01,1.344 false 1.49,4.396 1.74,4.094 false 2.115,4.396 1.875,4.094 false 0.188,2.469 0.542,2.802 0.354,0.333 10 false *1 3.021,2.479 3.406,2.802 0.385,0.323 10 false *2 1.823,3.302 2.177,3.51 0.354,0.208 10 false *4 2.552,1.615 2.906,1.885 0.354,0.271 10 false *5 0.531,0.135 0.958,0.552 0.427,0.417 10 false *a 0.594,3.729 1,4.083 0.406,0.354 10 false *b 0.188,3.146 0.542,3.479 0.354,0.333 10 false *3 2.698,2.479 3.083,2.802 0.385,0.323 10 false A 2.313,2.479 2.698,2.802 0.385,0.323 10 false B 0.625,2.479 1.01,2.802 0.385,0.323 10 false C 0.448,2.479 0.833,2.802 0.385,0.323 10 false D 0.823,3.156 1.208,3.479 0.385,0.323 10 false E 0.448,3.156 0.833,3.479 0.385,0.323 10 false F 0.813,0.542 1.167,0.844 0.354,0.302 10 false K73 2.531,0.938 3.01,1.208 0.479,0.271 10 false PAON 0.802,0.938 1.281,1.208 0.479,0.271 10 false P-AB 0.865,3.958 1.219,4.26 0.354,0.302 10 false K36 1.958,4.396 2.438,4.667 0.479,0.271 10 false PAON 1.302,4.396 1.781,4.667 0.479,0.271 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Telltale Light Assembly
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Telltale Light Assembly)


Connect the connector to the instrument panel junction block assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K36-5 (PAON) - Body ground Ignition switch ON Below 1 V
K36-4 (P-AB) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-5 (PAON) - K36-4 (P-AB) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K36-5 (PAON) - K36-4 (P-AB) Always 1 MΩ or higher
K36-5 (PAON) - Body ground Always 1 MΩ or higher
K36-4 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

14.CHECK INSTRUMENT PANEL WIRE
11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
a.
B474766C02
0.667,2.365 1.042,2.594 0.375,0.229 1.854,1.302 1.854,0.635 false 1.844,0.938 1.594,0.938 false 2.563,2.906 2.344,2.542 false 0.167,0.573 0.573,0.948 0.406,0.375 10 false *1 2.948,0.573 3.333,0.906 0.385,0.333 10 false *2 0.167,1.125 0.698,1.5 0.531,0.375 10 false *3 1.792,1.313 2.25,1.896 0.458,0.583 10 false *4 0.51,2.031 0.885,2.458 0.375,0.427 10 false *a 2.667,0.573 3.052,0.906 0.385,0.333 10 false A 2.292,0.573 2.677,0.906 0.385,0.333 10 false B 0.594,0.573 0.979,0.906 0.385,0.333 10 false C 0.406,0.573 0.792,0.906 0.385,0.333 10 false D 0.792,1.125 1.177,1.458 0.385,0.333 10 false E 0.417,1.125 0.802,1.458 0.385,0.333 10 false F 0.729,2.396 1.104,2.823 0.375,0.427 10 false K36 2.521,2.917 3.042,3.333 0.521,0.417 10 false IG+
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Telltale Light Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Telltale Light Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K36-10 (IG+) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

12.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE WIRE HARNESS OR BATTERY

12.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
B474767C01
0.667,1.958 1.063,2.198 0.396,0.24 2.167,2.885 2.552,2.615 false 2.083,2.885 1.229,2.604 false 1.75,1.135 1.75,0.552 false 1.5,0.833 1.75,0.833 false 0.26,0.458 0.698,0.823 0.438,0.365 10 false *1 2.854,0.469 3.229,0.781 0.375,0.313 10 false *2 0.271,1.021 0.698,1.49 0.427,0.469 10 false *3 1.677,1.156 2.073,1.49 0.396,0.333 10 false *4 0.469,1.552 0.917,2.146 0.448,0.594 10 false *a 0.74,1.99 1.188,2.583 0.448,0.594 10 false K73 2.594,2.531 3.135,3 0.542,0.469 10 false PAON 0.875,2.531 1.417,3 0.542,0.469 10 false P-AB 2.573,0.469 2.948,0.781 0.375,0.313 10 false A 2.198,0.469 2.573,0.781 0.375,0.313 10 false B 0.698,0.469 1.073,0.781 0.375,0.313 10 false C 0.5,0.469 0.875,0.781 0.375,0.313 10 false D 0.698,1.021 1.073,1.333 0.375,0.313 10 false E 0.5,1.021 0.875,1.333 0.375,0.313 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Telltale Light Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the connector to the telltale light assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator according to the conditions in the table below.

OK:
Terminal Connection Condition Specified Condition
K73-35 (PAON) - Body ground Ignition switch ON "ON" comes on
K73-34 (P-AB) - Body ground Ignition switch ON "OFF" comes on



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

13.CHECK DTC

NG

13.CHECK DTC
a.
C284134C01
0.271,0.802 0.583,1.073 0.313,0.271 10 false *1 2.906,0.813 3.219,1.104 0.313,0.292 10 false *2 0.292,1.469 0.719,1.917 0.427,0.448 10 false *3 2.615,0.802 2.927,1.146 0.313,0.344 10 false A 2.427,0.802 2.74,1.198 0.313,0.396 10 false B 0.74,0.802 1.042,1.177 0.302,0.375 10 false C 0.552,0.802 0.865,1.094 0.313,0.292 10 false D 0.729,1.479 1.083,1.979 0.354,0.5 10 false E 0.563,1.479 0.875,1.635 0.313,0.156 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Telltale Light Assembly


Connect the connector to the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

14.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the connector from the instrument panel junction block assembly.

B477424C01
3.375,0.094 3.708,0.292 0.333,0.198 4.094,2.75 4.427,2.948 0.333,0.198 1.313,3.042 1.646,3.24 0.333,0.198 3.667,2.427 3.667,1.76 false 3.469,2 3.667,2 false 2.906,1.125 3.719,0.604 false 3.417,1.135 3.656,0.833 false 4.031,1.125 4.177,0.719 false 4.552,1.135 4.271,0.833 false 5.302,3.646 5.635,3.646 false 5.24,3.396 5.521,3.156 false 5.167,3.396 4.49,3.156 false 2.156,3.573 2.156,3.427 false 2.104,3.188 1.76,3.458 false 2.208,3.188 2.542,3.458 false 2.292,1.688 2.677,2.021 0.385,0.333 10 false *1 2.292,2.146 2.708,2.51 0.417,0.365 10 false *3 4.573,1.698 5,2.156 0.427,0.458 10 false *2 3.604,2.448 3.99,2.802 0.385,0.354 10 false *4 2.292,0.083 2.719,0.51 0.427,0.427 10 false *a 4.344,1.688 4.771,2.146 0.427,0.458 10 false A 4.031,1.688 4.458,2.146 0.427,0.458 10 false B 2.813,1.688 3.24,2.146 0.427,0.458 10 false C 2.51,1.688 2.938,2.146 0.427,0.458 10 false D 2.813,2.135 3.24,2.594 0.427,0.458 10 false E 2.51,2.135 2.938,2.594 0.427,0.458 10 false F 3.969,2.438 4.396,2.865 0.427,0.427 10 false *b 1.26,2.823 1.688,3.25 0.427,0.427 10 false *c 3.458,0.115 3.844,0.469 0.385,0.354 10 false 3A 2.708,1.135 3.198,1.458 0.49,0.323 10 false PAON 3.24,1.135 3.729,1.458 0.49,0.323 10 false P-AB 3.844,1.135 4.333,1.458 0.49,0.323 10 false PAON 4.438,1.135 4.927,1.458 0.49,0.323 10 false P-AB 4.146,2.771 4.542,3.042 0.396,0.271 10 false K73 5.667,3.573 5.958,3.771 0.292,0.198 10 false *5 4.146,3.073 4.635,3.396 0.49,0.323 10 false P-AB 5.542,3.073 6.031,3.396 0.49,0.323 10 false PAON 2.094,3.583 2.396,3.792 0.302,0.208 10 false *5 1.583,3.458 2.073,3.781 0.49,0.323 10 false P-AB 2.385,3.458 2.875,3.781 0.49,0.323 10 false PAON 1.365,3.063 1.76,3.333 0.396,0.271 10 false K36
*1 Instrument Panel Junction Block Assembly *2 Airbag Sensor Assembly
*3 Telltale Light Assembly *4 Instrument Panel Wire
*5 Service Wire - -
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)
*c Front view of wire harness connector
(to Telltale Light Assembly)
- -



b.

Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


e.

Using a service wire, connect terminals 5 (PAON) and 4 (P-AB) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-29 (PAON) - 3A-51 (P-AB) Always Below 1 Ω



g.

Disconnect the service wire from connector E.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground or other terminals Always 1 MΩ or higher
3A-29 (PAON) - Body ground or other terminals Always 1 MΩ or higher
3A-46 (P-AB) - Body ground or other terminals Always 1 MΩ or higher
3A-51 (P-AB) - Body ground or other terminals Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE