Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327338 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800  Short in D Squib Circuit  B1801  Open in D Squib Circuit  B1802  Short in D Squib Circuit (to Ground)  B1803  Short in D Squib Circuit (to +B)  


DESCRIPTION

The driver squib circuit consists of the airbag sensor assembly, spiral cable sub-assembly and horn button assembly.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1800 Short in D Squib Circuit
·

The airbag sensor assembly detects a line short in the driver squib circuit during the primary check.

·

Spiral cable sub-assembly malfunction

·

Driver squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Driver squib (Horn button assembly)

·

Airbag sensor assembly


Comes on Applies to check mode
B1801 Open in D Squib Circuit
·

The airbag sensor assembly detects an open in the driver squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Driver squib (Horn button assembly)

·

Airbag sensor assembly


Comes on Applies to check mode
B1802 Short in D Squib Circuit (to Ground)
·

The airbag sensor assembly detects a short to ground in the driver squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Driver squib (Horn button assembly)

·

Airbag sensor assembly


Comes on Applies to check mode
B1803 Short in D Squib Circuit (to +B)
·

The airbag sensor assembly detects a short to B+ in the driver squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Driver squib (Horn button assembly)

·

Airbag sensor assembly


Comes on Applies to check mode

WIRING DIAGRAM

w/ Occupant Classification System:
B475053E06
4.948,1.344 5.333,1.625 0.385,0.281 10 false D+ 4.948,1.896 5.333,2.177 0.385,0.281 10 false D- 4.771,1.344 5.156,1.625 0.385,0.281 10 false 6 4.771,1.896 5.156,2.177 0.385,0.281 10 false 7 4.917,2.917 5.427,3.219 0.51,0.302 10 false K73 4.917,3.083 6.594,3.427 1.677,0.344 10 false Airbag Sensor Assembly 3.229,1.438 3.74,1.74 0.51,0.302 10 false K24 3.229,2 3.74,2.302 0.51,0.302 10 false K24 3.302,1.229 3.813,1.531 0.51,0.302 10 false 1 3.302,1.781 3.813,2.083 0.51,0.302 10 false 2 2.396,2.406 3.365,2.854 0.969,0.448 10 false Spiral Cable Sub-assembly 2.917,1.344 3.302,1.625 0.385,0.281 10 false D+ 2.948,1.896 3.333,2.177 0.385,0.281 10 false D- 2.458,1.344 2.844,1.625 0.385,0.281 10 false D+ 2.458,1.896 2.844,2.177 0.385,0.281 10 false D- 2.146,1.438 2.656,1.74 0.51,0.302 10 false z2 2.146,1.99 2.656,2.292 0.51,0.302 10 false z2 1.802,1.344 2.188,1.625 0.385,0.281 10 false D+ 1.823,1.896 2.208,2.177 0.385,0.281 10 false D- 0.865,2.417 2.083,2.99 1.219,0.573 10 false Driver Squib (Horn Button Assembly) 2.177,1.229 2.688,1.531 0.51,0.302 10 false 2 2.177,1.781 2.688,2.083 0.51,0.302 10 false 1

w/o Occupant Classification System:
B475053E11
4.948,1.344 5.333,1.625 0.385,0.281 10 false D+ 4.948,1.896 5.333,2.177 0.385,0.281 10 false D- 4.771,1.344 5.156,1.625 0.385,0.281 10 false 6 4.771,1.896 5.156,2.177 0.385,0.281 10 false 7 4.917,2.917 5.427,3.219 0.51,0.302 10 false K73 4.917,3.083 6.594,3.427 1.677,0.344 10 false Airbag Sensor Assembly 3.229,1.438 3.74,1.74 0.51,0.302 10 false K24 3.229,2 3.74,2.302 0.51,0.302 10 false K24 3.302,1.229 3.813,1.531 0.51,0.302 10 false 1 3.302,1.781 3.813,2.083 0.51,0.302 10 false 2 2.396,2.406 3.365,2.854 0.969,0.448 10 false Spiral Cable Sub-assembly 2.917,1.344 3.302,1.625 0.385,0.281 10 false D+ 2.948,1.896 3.333,2.177 0.385,0.281 10 false D- 2.458,1.344 2.844,1.625 0.385,0.281 10 false D+ 2.458,1.896 2.844,2.177 0.385,0.281 10 false D- 2.146,1.438 2.656,1.74 0.51,0.302 10 false z9 2.146,1.99 2.656,2.292 0.51,0.302 10 false z9 1.802,1.344 2.188,1.625 0.385,0.281 10 false D+ 1.823,1.896 2.208,2.177 0.385,0.281 10 false D- 0.865,2.417 2.083,2.99 1.219,0.573 10 false Driver Squib (Horn Button Assembly) 2.177,1.229 2.688,1.531 0.51,0.302 10 false 2 2.177,1.781 2.688,2.083 0.51,0.302 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Occupant Classification System A
w/o Occupant Classification System B



A

2.CHECK CONNECTORS

B

8.CHECK CONNECTORS
2.CHECK CONNECTORS
a.
C238331C01
1.979,1.083 1.979,1.469 false 0.271,1.083 0.271,1.469 false 0.208,1.49 0.729,1.844 0.521,0.354 10 false *1 1.052,0.948 1.563,1.292 0.51,0.344 10 false *2 2.75,0.969 3.229,1.292 0.479,0.323 10 false *3 1.906,1.49 2.323,1.792 0.417,0.302 10 false *4 2.365,0.938 2.74,1.323 0.375,0.385 10 false A 2.104,0.938 2.448,1.438 0.344,0.5 10 false B 1.76,0.948 2.135,1.229 0.375,0.281 10 false C 1.5,0.948 1.948,1.333 0.448,0.385 10 false D 0.656,0.948 1.344,1.49 0.688,0.542 10 false E 0.396,0.948 1,1.323 0.604,0.375 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Instrument Panel Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral cable sub-assembly connector (on the horn button assembly side) is not loose, deformed or damaged.

OK:

The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and spiral cable sub-assembly connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK HORN BUTTON ASSEMBLY

NG

REPLACE WIRE HARNESS

3.CHECK HORN BUTTON ASSEMBLY
a.
C348746C16
0.427,2.156 0.74,2.375 0.313,0.219 2,2.25 1.75,2.25 false 1.281,2.396 0.865,2.854 false 0.313,0.76 0.313,1.177 false 0.25,1.198 0.646,1.5 0.396,0.302 10 false *1 1.156,0.625 1.604,1.01 0.448,0.385 10 false *2 2.729,0.615 3.177,0.969 0.448,0.354 10 false *3 0.302,1.677 0.698,2.167 0.396,0.49 10 false *a 0.698,2.781 1.01,2.938 0.313,0.156 10 false *b 2.042,2.167 2.521,2.583 0.479,0.417 10 false SST 0.51,2.188 0.875,2.49 0.365,0.302 10 false z2 2.344,0.615 2.792,0.969 0.448,0.354 10 false A 2.177,0.615 2.625,0.969 0.448,0.354 10 false B 1.76,0.615 2.208,0.969 0.448,0.354 10 false C 1.594,0.615 2.042,0.969 0.448,0.354 10 false D 0.75,0.615 1.198,0.969 0.448,0.354 10 false E 0.438,0.615 0.885,0.969 0.448,0.354 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Connect the instrument panel wire to the airbag sensor assembly and spiral cable sub-assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E (light green connector).

CAUTION:

Never connect a tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTCs B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Disconnect SST from connector E.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK DRIVER SQUIB CIRCUIT
4.CHECK DRIVER SQUIB CIRCUIT
a.
C348747C17
0.469,2.156 0.823,2.396 0.354,0.24 0.271,1.208 0.271,0.875 false 1.25,2.104 1.031,1.823 false 1.375,2.104 1.594,1.833 false 1.313,2.427 1.729,2.833 false 0.208,1.219 0.573,1.521 0.365,0.302 10 false *1 1.104,0.719 1.51,1.198 0.406,0.479 10 false *2 2.76,0.729 3.219,1.219 0.458,0.49 10 false *3 0.302,1.688 0.698,2.021 0.396,0.333 10 false *a 1.771,2.76 2.167,3.083 0.396,0.323 10 false *b 0.583,2.188 0.99,2.667 0.406,0.479 10 false z2 1.635,1.75 2.083,2.135 0.448,0.385 10 false D+ 0.854,1.75 1.302,2.135 0.448,0.385 10 false D- 2.375,0.729 2.833,1.219 0.458,0.49 10 false A 2.063,0.729 2.521,1.219 0.458,0.49 10 false B 1.708,0.729 2.167,1.219 0.458,0.49 10 false C 1.552,0.729 2.01,1.219 0.458,0.49 10 false D 0.698,0.729 1.156,1.219 0.458,0.49 10 false E 0.375,0.729 0.833,1.219 0.458,0.49 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Disconnect the instrument panel wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z2-2 (D+) - Body ground Ignition switch ON Below 1 V
z2-1 (D-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (D+) - z2-1 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (D+) - Body ground Always 1 MΩ or higher
z2-1 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (D+) - z2-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

6.CHECK INSTRUMENT PANEL WIRE
5.CHECK DTC
a.
C238334C01
0.313,1.01 0.313,0.344 0.313,0.344 0.563,0.344 false 0.594,0.26 1.063,0.521 0.469,0.26 10 false *1 0.427,1.01 1.031,1.688 0.604,0.677 10 false F 0.583,1.01 1.021,1.573 0.438,0.563 10 false E 1.51,1.01 1.729,1.385 0.219,0.375 10 false D 1.667,1.01 1.917,1.375 0.25,0.365 10 false C 2.094,1.01 2.49,1.354 0.396,0.344 10 false B 2.25,1.01 2.542,1.292 0.292,0.281 10 false A 1,1.01 1.49,1.656 0.49,0.646 10 false *2 2.667,1.021 2.979,1.365 0.313,0.344 10 false *3
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly


Connect the connectors to the horn button assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTCs B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK INSTRUMENT PANEL WIRE
a.
C238335C36
0.5,2.427 0.865,2.656 0.365,0.229 0.281,0.948 0.281,1.229 false 1.281,2.604 1.063,2.958 false 1.438,2.594 1.667,2.948 false 1.969,0.823 1.969,0.396 1.969,0.396 1.802,0.396 false 0.563,2.458 0.958,2.875 0.396,0.417 10 false K24 0.396,0.802 0.583,1.208 0.188,0.406 10 false F 0.667,0.802 0.906,1.26 0.24,0.458 10 false E 1.49,0.813 1.813,1.083 0.323,0.271 10 false D 1.75,0.813 2.094,1.271 0.344,0.458 10 false C 2.104,0.813 2.531,1.292 0.427,0.479 10 false B 2.365,0.813 2.854,1.313 0.49,0.5 10 false A 1.042,0.823 1.458,1.156 0.417,0.333 10 false *2 0.208,1.25 0.667,1.594 0.458,0.344 10 false *1 2.74,0.823 3.146,1.26 0.406,0.438 10 false *3 0.344,1.969 0.719,2.313 0.375,0.344 10 false *a 1.646,2.958 2.042,3.167 0.396,0.208 10 false D- 1.646,0.323 1.979,0.604 0.333,0.281 10 false *4 0.969,2.969 1.563,3.219 0.594,0.25 10 false D+
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the instrument panel wire from the spiral cable sub-assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K24-1 (D+) - Body ground Ignition switch ON Below 1 V
K24-2 (D-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K24-1 (D+) - K24-2 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K24-1 (D+) - Body ground Always 1 MΩ or higher
K24-2 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K24-1 (D+) - K24-2 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

7.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK SPIRAL CABLE SUB-ASSEMBLY
a.
C348748C17
0.531,2.188 0.854,2.396 0.323,0.208 0.25,1.125 0.25,0.875 false 1.979,1.125 1.979,0.875 false 0.927,1.833 1.24,2.115 false 1.667,1.833 1.365,2.115 false 1.771,2.729 1.313,2.448 false 0.188,1.146 0.542,1.469 0.354,0.323 10 false *1 1.031,0.729 1.469,1.073 0.438,0.344 10 false *2 2.781,0.729 3.24,1.156 0.458,0.427 10 false *3 1.917,1.146 2.323,1.604 0.406,0.458 10 false *4 0.333,1.698 0.729,2.188 0.396,0.49 10 false *a 1.813,2.656 2.24,2.948 0.427,0.292 10 false *b 0.625,2.208 1.052,2.5 0.427,0.292 10 false z2 1.698,1.75 2.125,2.042 0.427,0.292 10 false D+ 0.75,1.75 1.177,2.042 0.427,0.292 10 false D- 2.385,0.729 2.844,1.156 0.458,0.427 10 false A 2.104,0.729 2.563,1.156 0.458,0.427 10 false B 1.76,0.729 2.219,1.156 0.458,0.427 10 false C 1.479,0.729 1.938,1.156 0.458,0.427 10 false D 0.656,0.729 1.115,1.156 0.458,0.427 10 false E 0.375,0.729 0.833,1.156 0.458,0.427 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Light Green


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z2-2 (D+) - Body ground Ignition switch ON Below 1 V
z2-1 (D-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (D+) - z2-1 (D-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (D+) - Body ground Always 1 MΩ or higher
z2-1 (D-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-2 (D+) - z2-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.



Result:
Proceed to
OK
NG



OK

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

8.CHECK CONNECTORS
a.
C238331C01
1.979,1.083 1.979,1.469 false 0.271,1.083 0.271,1.469 false 0.208,1.49 0.729,1.844 0.521,0.354 10 false *1 1.052,0.948 1.563,1.292 0.51,0.344 10 false *2 2.75,0.969 3.229,1.292 0.479,0.323 10 false *3 1.906,1.49 2.323,1.792 0.417,0.302 10 false *4 2.365,0.938 2.74,1.323 0.375,0.385 10 false A 2.104,0.938 2.448,1.438 0.344,0.5 10 false B 1.76,0.948 2.135,1.229 0.375,0.281 10 false C 1.5,0.948 1.948,1.333 0.448,0.385 10 false D 0.656,0.948 1.344,1.49 0.688,0.542 10 false E 0.396,0.948 1,1.323 0.604,0.375 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Instrument Panel Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral cable sub-assembly connector (on the horn button assembly side) is not loose, deformed or damaged.

OK:

The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and spiral cable sub-assembly connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

9.CHECK HORN BUTTON ASSEMBLY

NG

REPLACE WIRE HARNESS

9.CHECK HORN BUTTON ASSEMBLY
a.
C361088C15
0.365,2.146 0.688,2.385 0.323,0.24 0.323,1.104 0.323,0.771 false 1.979,2.333 1.729,2.333 false 0.26,1.125 0.594,1.417 0.333,0.292 10 false *1 1.146,0.625 1.531,0.948 0.385,0.323 10 false *2 2.719,0.615 3.104,1 0.385,0.385 10 false *3 0.333,1.708 0.708,2.198 0.375,0.49 10 false *a 2.333,0.615 2.719,1 0.385,0.385 10 false A 2.177,0.615 2.563,1 0.385,0.385 10 false B 1.75,0.615 2.135,1 0.385,0.385 10 false C 1.594,0.615 1.979,1 0.385,0.385 10 false D 0.75,0.615 1.135,1 0.385,0.385 10 false E 0.438,0.615 0.823,1 0.385,0.385 10 false F 0.458,2.188 0.833,2.677 0.375,0.49 10 false z9 2.021,2.25 2.448,2.635 0.427,0.385 10 false SST
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)


Connect the instrument panel wire to the airbag sensor assembly and spiral cable sub-assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect a tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTCs B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Disconnect SST from connector E.


Result:
Proceed to
OK
NG



OK

NG

10.CHECK DRIVER SQUIB CIRCUIT
10.CHECK DRIVER SQUIB CIRCUIT
a.
C361089C16
0.552,2.177 0.896,2.417 0.344,0.24 0.26,1.198 0.26,0.865 false 1,1.833 1.323,2.104 false 1.802,1.833 1.458,2.104 false 0.198,1.208 0.594,1.656 0.396,0.448 10 false *1 1.094,0.719 1.5,1.063 0.406,0.344 10 false *2 2.75,0.729 3.188,1.469 0.438,0.74 10 false *3 0.313,1.688 0.802,2.302 0.49,0.615 10 false *a 0.667,2.219 1.063,2.667 0.396,0.448 10 false z9 1.844,1.75 2.24,2.198 0.396,0.448 10 false D+ 0.802,1.75 1.198,2.198 0.396,0.448 10 false D- 2.385,0.729 2.823,1.469 0.438,0.74 10 false A 2.063,0.729 2.5,1.469 0.438,0.74 10 false B 1.708,0.729 2.146,1.469 0.438,0.74 10 false C 1.552,0.729 1.99,1.469 0.438,0.74 10 false D 0.698,0.729 1.135,1.469 0.438,0.74 10 false E 0.375,0.729 0.813,1.469 0.438,0.74 10 false F
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)


Disconnect the instrument panel wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z9-2 (D+) - Body ground Ignition switch ON Below 1 V
z9-1 (D-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-2 (D+) - z9-1 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-2 (D+) - Body ground Always 1 MΩ or higher
z9-1 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-2 (D+) - z9-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

11.CHECK DTC

NG

12.CHECK INSTRUMENT PANEL WIRE
11.CHECK DTC
a.
C238334C01
0.313,1.01 0.313,0.344 0.313,0.344 0.563,0.344 false 0.594,0.26 1.063,0.521 0.469,0.26 10 false *1 0.427,1.01 1.031,1.688 0.604,0.677 10 false F 0.583,1.01 1.021,1.573 0.438,0.563 10 false E 1.51,1.01 1.729,1.385 0.219,0.375 10 false D 1.667,1.01 1.917,1.375 0.25,0.365 10 false C 2.094,1.01 2.49,1.354 0.396,0.344 10 false B 2.25,1.01 2.542,1.292 0.292,0.281 10 false A 1,1.01 1.49,1.656 0.49,0.646 10 false *2 2.667,1.021 2.979,1.365 0.313,0.344 10 false *3
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly


Connect the connectors to the horn button assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTCs B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

12.CHECK INSTRUMENT PANEL WIRE
a.
C238335C36
0.5,2.427 0.865,2.656 0.365,0.229 0.281,0.948 0.281,1.229 false 1.281,2.604 1.063,2.958 false 1.438,2.594 1.667,2.948 false 1.969,0.823 1.969,0.396 1.969,0.396 1.802,0.396 false 0.563,2.458 0.958,2.875 0.396,0.417 10 false K24 0.396,0.802 0.583,1.208 0.188,0.406 10 false F 0.667,0.802 0.906,1.26 0.24,0.458 10 false E 1.49,0.813 1.813,1.083 0.323,0.271 10 false D 1.75,0.813 2.094,1.271 0.344,0.458 10 false C 2.104,0.813 2.531,1.292 0.427,0.479 10 false B 2.365,0.813 2.854,1.313 0.49,0.5 10 false A 1.042,0.823 1.458,1.156 0.417,0.333 10 false *2 0.208,1.25 0.667,1.594 0.458,0.344 10 false *1 2.74,0.823 3.146,1.26 0.406,0.438 10 false *3 0.344,1.969 0.719,2.313 0.375,0.344 10 false *a 1.646,2.958 2.042,3.167 0.396,0.208 10 false D- 1.646,0.323 1.979,0.604 0.333,0.281 10 false *4 0.969,2.969 1.563,3.219 0.594,0.25 10 false D+
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the instrument panel wire from the spiral cable sub-assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K24-1 (D+) - Body ground Ignition switch ON Below 1 V
K24-2 (D-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K24-1 (D+) - K24-2 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K24-1 (D+) - Body ground Always 1 MΩ or higher
K24-2 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K24-1 (D+) - K24-2 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

13.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

13.CHECK SPIRAL CABLE SUB-ASSEMBLY
a.
C361090C16
0.563,2.146 0.896,2.375 0.333,0.229 0.26,1.208 0.26,0.875 false 1.969,0.74 1.969,0.323 1.969,0.323 1.802,0.323 false 1.01,1.823 1.323,2.125 false 1.771,1.833 1.469,2.115 false 0.198,1.219 0.615,1.552 0.417,0.333 10 false *1 1.042,0.729 1.521,1.219 0.479,0.49 10 false *2 2.781,0.729 3.198,1.323 0.417,0.594 10 false *3 1.656,0.25 2.01,0.573 0.354,0.323 10 false *4 0.333,1.708 0.729,2.198 0.396,0.49 10 false *a 2.385,0.729 2.802,1.323 0.417,0.594 10 false A 2.104,0.729 2.521,1.323 0.417,0.594 10 false B 1.76,0.729 2.177,1.323 0.417,0.594 10 false C 1.479,0.729 1.896,1.323 0.417,0.594 10 false D 0.656,0.729 1.073,1.323 0.417,0.594 10 false E 0.375,0.729 0.792,1.323 0.417,0.594 10 false F 0.667,2.177 1.063,2.594 0.396,0.417 10 false z9 0.823,1.75 1.219,2.167 0.396,0.417 10 false D- 1.823,1.75 2.219,2.167 0.396,0.417 10 false D+
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Horn Button Assembly)


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z9-2 (D+) - Body ground Ignition switch ON Below 1 V
z9-1 (D-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-2 (D+) - z9-1 (D-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-2 (D+) - Body ground Always 1 MΩ or higher
z9-1 (D-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SYSTEM DESCRIPTION


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-2 (D+) - z9-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.



Result:
Proceed to
OK
NG



OK

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY