Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327338 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B163B  Side Airbag Sensor Assembly No.2 Lost Communication (LH)  B163C  Side Airbag Sensor Assembly No.2 Initialization Error (LH)  B1699  No.2 Side Satellite Sensor Bus LH Initialization Incomplete  


DESCRIPTION

The side collision sensor LH circuit (bus 2) consists of the airbag sensor assembly and side No. 1 airbag sensor LH.

The side No. 1 airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 2).

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B163B Side Airbag Sensor Assembly No.2 Lost Communication (LH)
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 2).

·

Side No. 1 airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side No. 1 airbag sensor LH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode
B163C Side Airbag Sensor Assembly No.2 Initialization Error (LH)
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 2).

·

Side No. 1 airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side No. 1 airbag sensor LH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode
B1699 No.2 Side Satellite Sensor Bus LH Initialization Incomplete
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 2).

·

Side No. 1 airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side No. 1 airbag sensor LH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B473434E08
4.781,2.917 6.49,3.354 1.708,0.438 10 false Airbag Sensor Assembly 4.771,2.74 5.885,3.167 1.115,0.427 10 false R32 4.823,1.01 5.938,1.438 1.115,0.427 10 false BCL+ 5.49,1.458 6.604,1.885 1.115,0.427 10 false Interface 4.583,1.01 5.698,1.438 1.115,0.427 10 false 29 4.823,1.688 5.938,2.115 1.115,0.427 10 false BCL- 4.583,1.688 5.698,2.115 1.115,0.427 10 false 30 2.604,1.01 3.719,1.438 1.115,0.427 10 false BFL+ 2.615,1.698 3.729,2.125 1.115,0.427 10 false BFL- 3.052,1.01 4.167,1.438 1.115,0.427 10 false 2 3.052,1.698 4.167,2.125 1.115,0.427 10 false 1 1.771,1.458 2.885,1.885 1.115,0.427 10 false Interface 0.771,1.458 1.885,1.885 1.115,0.427 10 false Element 0.552,2.344 1.667,2.771 1.115,0.427 10 false R36 0.552,2.521 3.354,2.906 2.802,0.385 10 false Side No. 1 Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and side No. 1 airbag sensor LH.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and side No. 1 airbag sensor LH.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE
a.
B474701C01
0.844,0.844 1.188,1.073 0.344,0.229 0.99,3.729 1.333,3.958 0.344,0.229 2.073,1.813 2.073,1.677 false 1.667,1.729 2.01,1.302 false 2.5,1.74 2.125,1.302 false 1.635,2.927 1.635,2.51 false 1.5,4.271 1.802,3.844 false 2.333,4.271 1.99,3.844 false 0.75,2.375 1.188,2.833 0.438,0.458 10 false *1 2.51,2.656 2.958,3.125 0.448,0.469 10 false *2 1.563,2.927 2.021,3.365 0.458,0.438 10 false *3 2,1.813 2.427,2.208 0.427,0.396 10 false *4 0.677,0.188 1.177,0.688 0.5,0.5 10 false *a 0.708,3.427 1.156,3.813 0.448,0.385 10 false *b 2.188,2.375 2.635,2.844 0.448,0.469 10 false A 1.885,2.375 2.333,2.844 0.448,0.469 10 false B 1.292,2.375 1.74,2.844 0.448,0.469 10 false C 0.979,2.375 1.427,2.844 0.448,0.469 10 false D 1.042,3.771 1.49,4.156 0.448,0.385 10 false R36 0.896,0.875 1.344,1.26 0.448,0.385 10 false R32 2.385,1.74 2.833,2.125 0.448,0.385 10 false BCL- 1.5,1.74 1.948,2.125 0.448,0.385 10 false BCL+ 2.219,4.271 2.677,4.563 0.458,0.292 10 false BFL+ 1.365,4.271 1.865,4.573 0.5,0.302 10 false BFL-
*1 Side No. 1 Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side No. 1 Airbag Sensor LH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R36-2 (BFL+) - Body ground Ignition switch ON Below 1 V
R36-1 (BFL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 29 (BCL+) and 30 (BCL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R36-2 (BFL+) - R36-1 (BFL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R36-2 (BFL+) - R36-1 (BFL-) Always 1 MΩ or higher
R36-2 (BFL+) - Body ground Always 1 MΩ or higher
R36-1 (BFL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SIDE NO. 1 AIRBAG SENSOR LH

NG

REPLACE FLOOR WIRE

4.CHECK SIDE NO. 1 AIRBAG SENSOR LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side No. 1 Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the side No. 1 airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B162B, B162C, B163B, B163C, B1694 and B1699 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B163B, B163C or B1699 is output. A
DTC B162B, B162C or B1694 is output. B
DTCs B162B, B162C, B163B, B163C, B1694 and B1699 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side No. 1 airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C