Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327345 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 62180A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

NOTICE:

When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Insert the 3 hooks, install the curtain shield airbag assembly with 4 new bolts, a new spacer, 4 new clips (A) with pins, and engage the 5 clips (B) in the order shown in the illustration.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.


HINT:

Engage the 2 claws to install each new clip (A).


B489945C01
1.677,2.385 1.865,2.385 1.865,2.385 1.979,2.156 true 6.115,1.021 6.115,0.615 6.115,0.615 6.406,0.615 true 3.958,2.125 4.188,2.125 true 5.26,2.052 5.479,2.052 true 5.51,1.979 5.823,2.135 0.313,0.156 10 false *1 1.26,1.5 1.573,1.656 0.313,0.156 10 false *a 0.292,0.615 0.479,0.813 0.188,0.198 10 true *b 1.51,2.292 1.688,2.49 0.177,0.198 10 false *2 6.417,0.521 6.604,0.708 0.188,0.188 10 true *c 4.219,2.063 4.531,2.219 0.313,0.156 10 false *1 1.552,0.365 1.74,0.563 0.188,0.198 10 true *b 3.573,0.833 3.76,1.031 0.188,0.198 10 true *b 4.51,0.292 4.698,0.49 0.188,0.198 10 true *b 5.531,0.51 5.719,0.708 0.188,0.198 10 true *b 2.521,0.635 2.656,0.823 0.135,0.188 10 true 1 2.344,0.646 2.479,0.833 0.135,0.188 10 true 2 2.563,0.115 2.698,0.302 0.135,0.188 10 true 3 2.24,0.104 2.375,0.292 0.135,0.188 10 true 4 1.615,0.771 1.75,0.958 0.135,0.188 10 true 5 0.365,1.031 0.5,1.219 0.135,0.188 10 true 6 0.99,0.302 1.125,0.49 0.135,0.188 10 true 7 1.948,0.354 2.063,0.542 0.115,0.188 10 true 8 4.042,0.26 4.156,0.448 0.115,0.188 10 true 9 3.552,0.448 3.74,0.625 0.188,0.177 10 true 10 5.104,0.375 5.292,0.552 0.188,0.177 10 true 11 4.552,0.698 4.74,0.875 0.188,0.177 10 true 12 5.573,0.917 5.76,1.094 0.188,0.177 10 true 13 6.198,0.927 6.385,1.104 0.188,0.177 10 true 14 6.917,1.542 7.104,1.719 0.188,0.177 10 true 15 6.781,1.021 6.969,1.208 0.188,0.188 10 true 16
*1 Pin *2 Spacer
*a Clip (A) *b Clip (B)
*c Spacer Location - -
V113147

Install in this Direction - -



d.

Using needle nose pliers, push the 4 pins into the 4 clips (A).

NOTICE:
·

Do not damage the pins.

·

Make sure that the pins of the clips (A) are pushed in firmly.




e.
B489946C01
2.156,0.292 2.396,0.292 2.396,0.292 2.604,0.635 true 1.677,2.25 1.979,1.854 1.979,1.854 2.177,1.854 true 2.198,1.75 2.406,1.958 0.208,0.208 10 true *a 1.979,0.198 2.292,0.354 0.313,0.156 10 false *b
*a Airbag Connector
*b Airbag Connector Locking Button
V113147

Push in this Direction


Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



f.

Push in the airbag connector locking button to install the airbag connector.


Hide 2.INSTALL ROOF HEADLINING ASSEMBLY