Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327338 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1653  Driver Side Seat Position Sensor  


DESCRIPTION

The seat position sensor circuit consists of the airbag sensor assembly and seat position sensor (front seat adjuster assembly LH).

DTC B1653 is stored when a malfunction is detected in the seat position sensor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1653 Driver Side Seat Position Sensor
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the seat position sensor circuit.

·

Seat position sensor malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat No. 3 wire LH

·

Front seat inner belt assembly LH

·

Seat position sensor (Front seat adjuster assembly LH)*

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

*: The seat position sensor is built into the front seat adjuster assembly LH.


WIRING DIAGRAM

B474704E03
5.333,1.073 5.854,1.406 0.521,0.333 10 false LSP+ 5.333,1.99 5.792,2.302 0.458,0.313 10 false LSP- 5.094,1.073 5.417,1.406 0.323,0.333 10 false 25 5.083,1.99 5.396,2.375 0.313,0.385 10 false 26 2.844,2.521 4.24,2.938 1.396,0.417 10 false Front Seat Inner Belt Assembly LH 4.177,2.104 4.594,2.385 0.417,0.281 10 false R69 4.177,1.188 4.594,1.469 0.417,0.281 10 false R69 4.26,0.969 4.677,1.25 0.417,0.281 10 false 4 4.26,1.885 4.677,2.167 0.417,0.281 10 false 3 3.719,1.073 4.333,1.271 0.615,0.198 10 false LSP+ 2.906,1.073 3.521,1.271 0.615,0.198 10 false LSP+ 3.729,1.99 4.344,2.188 0.615,0.198 10 false LSP- 2.906,1.99 3.521,2.188 0.615,0.198 10 false LSP- 2.615,1.177 3.031,1.458 0.417,0.281 10 false F 2.615,2.094 3.031,2.375 0.417,0.281 10 false F 2.625,0.969 3.042,1.25 0.417,0.281 10 false 2 1.719,1.083 2.135,1.365 0.417,0.281 10 false 2 0.406,2.521 0.823,2.802 0.417,0.281 10 false G 0.396,2.677 2.177,3.167 1.781,0.49 10 false Seat Position Sensor (Front Seat Adjuster Assembly LH) 1.281,1.083 1.896,1.281 0.615,0.198 10 false LSP+ 1.302,1.99 1.917,2.188 0.615,0.198 10 false LSP- 2.615,1.885 3.031,2.167 0.417,0.281 10 false 1 1.719,1.99 2.135,2.271 0.417,0.281 10 false 1 5.281,2.917 6.74,3.375 1.458,0.458 10 false R32 5.281,3.083 7.031,3.49 1.75,0.406 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, front seat inner belt assembly LH and seat position sensor.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, front seat inner belt assembly LH and seat position sensor.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS

NG

REPLACE FLOOR WIRE, FRONT SEAT NO. 3 WIRE LH OR FRONT SEAT INNER BELT ASSEMBLY LH

3.CHECK WIRE HARNESS
a.

Connect the floor wire and front seat No. 3 wire LH to the front seat inner belt assembly LH.

B473435C01
1.813,2.906 2.135,3.125 0.323,0.219 3.604,0.823 3.927,1.042 0.323,0.219 4.313,1.625 4.313,1.51 false 3.906,1.5 4.271,1.198 false 4.677,1.49 4.354,1.198 false 2.271,3.365 2.573,3.021 false 2.99,3.365 2.698,3.021 false 2.729,2.167 2.729,1.583 2.729,1.583 2.479,1.583 false 4.083,2.583 4.083,2.208 false 2.021,2.104 2.385,2.385 0.365,0.281 10 false *1 3.344,2.104 3.781,2.479 0.438,0.375 10 false *2 4.781,2.333 5.26,2.885 0.479,0.552 10 false *3 2.333,1.51 2.729,1.865 0.396,0.354 10 false *4 4.01,2.583 4.469,3.01 0.458,0.427 10 false *5 4.25,1.635 4.656,1.958 0.406,0.323 10 false *6 3.438,0.24 3.938,1.031 0.5,0.792 10 false *a 1.656,2.656 2.094,3.063 0.438,0.406 10 false *b 3.76,1.51 4.188,1.865 0.427,0.354 10 false LSP+ 4.573,1.51 5.052,1.865 0.479,0.354 10 false LSP- 3.646,0.854 4.073,1.208 0.427,0.354 10 false R32 2.875,3.375 3.354,3.729 0.479,0.354 10 false LSP+ 2.135,3.375 2.615,3.729 0.479,0.354 10 false LSP- 1.927,2.938 2.406,3.292 0.479,0.354 10 false G 4.521,2.115 5,2.667 0.479,0.552 10 false A 4.26,2.115 4.74,2.667 0.479,0.552 10 false B 3.833,2.115 4.313,2.667 0.479,0.552 10 false C 3.708,2.115 4.188,2.667 0.479,0.552 10 false D 3.042,2.115 3.521,2.667 0.479,0.552 10 false E 2.917,2.115 3.396,2.667 0.479,0.552 10 false F 2.479,2.115 2.958,2.667 0.479,0.552 10 false G 2.219,2.115 2.698,2.667 0.479,0.552 10 false H
*1 Seat Position Sensor *2 Front Seat Inner Belt Assembly LH
*3 Airbag Sensor Assembly *4 Front Seat No. 3 Wire LH
*5 Floor Wire *6 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Seat Position Sensor)



b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G-2 (LSP+) - Body ground Ignition switch ON Below 1 V
G-1 (LSP-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G-2 (LSP+) - G-1 (LSP-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G-2 (LSP+) - G-1 (LSP-) Always 1 MΩ or higher
G-2 (LSP+) - Body ground Always 1 MΩ or higher
G-1 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

6.CHECK WIRE HARNESS
4.CHECK DTC
a.
B474758C01
0.177,0.781 0.625,1.167 0.448,0.385 10 false *1 2.875,1.052 3.344,1.469 0.469,0.417 10 false *3 2.552,0.781 3.021,1.198 0.469,0.417 10 false A 2.396,0.781 2.865,1.198 0.469,0.417 10 false B 2.042,0.781 2.51,1.198 0.469,0.417 10 false C 1.885,0.781 2.354,1.198 0.469,0.417 10 false D 1.063,0.781 1.531,1.198 0.469,0.417 10 false E 0.906,0.781 1.375,1.198 0.469,0.417 10 false F 0.552,0.781 1.021,1.198 0.469,0.417 10 false G 0.396,0.781 0.865,1.198 0.469,0.417 10 false H 1.438,0.771 1.906,1.188 0.469,0.417 10 false *2
*1 Seat Position Sensor
*2 Front Seat Inner Belt Assembly LH
*3 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and seat position sensor.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653 is not output.


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

5.CHECK AIRBAG SENSOR ASSEMBLY
5.CHECK AIRBAG SENSOR ASSEMBLY
a.
B474758C01
0.177,0.781 0.625,1.167 0.448,0.385 10 false *1 2.875,1.052 3.344,1.469 0.469,0.417 10 false *3 2.552,0.781 3.021,1.198 0.469,0.417 10 false A 2.396,0.781 2.865,1.198 0.469,0.417 10 false B 2.042,0.781 2.51,1.198 0.469,0.417 10 false C 1.885,0.781 2.354,1.198 0.469,0.417 10 false D 1.063,0.781 1.531,1.198 0.469,0.417 10 false E 0.906,0.781 1.375,1.198 0.469,0.417 10 false F 0.552,0.781 1.021,1.198 0.469,0.417 10 false G 0.396,0.781 0.865,1.198 0.469,0.417 10 false H 1.438,0.771 1.906,1.188 0.469,0.417 10 false *2
*1 Seat Position Sensor
*2 Front Seat Inner Belt Assembly LH
*3 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Replace the airbag sensor assembly with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653 is not output.


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Restore the airbag sensor assembly that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
OK
NG



OK

NG

REPLACE SEAT POSITION SENSOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

6.CHECK WIRE HARNESS
a.

Disconnect the front seat No. 3 wire LH connector from the front seat inner belt assembly LH.

B474706C01
3.646,0.802 3.979,1.021 0.333,0.219 2.49,2.875 2.76,3.083 0.271,0.208 4.375,1.625 4.375,1.51 false 4.021,1.542 4.333,1.198 false 4.729,1.542 4.427,1.198 false 2.885,3.333 3.146,2.99 false 3.594,3.333 3.354,3 false 2.667,2.167 2.667,1.583 2.667,1.583 2.5,1.583 false 4.448,2.969 4.167,2.208 false 1.927,2.115 2.344,2.479 0.417,0.365 10 false *1 3.406,2.115 3.875,2.563 0.469,0.448 10 false *2 4.854,2.323 5.385,2.833 0.531,0.51 10 false *3 2.365,1.51 2.854,1.896 0.49,0.385 10 false *4 4.396,2.969 4.844,3.396 0.448,0.427 10 false *5 4.302,1.635 4.75,1.969 0.448,0.333 10 false *6 3.521,0.24 4.042,0.76 0.521,0.521 10 false *a 2.292,2.656 2.677,2.969 0.385,0.313 10 false *b 3.698,0.833 4.219,1.354 0.521,0.521 10 false R32 4.604,1.542 5.125,2.063 0.521,0.521 10 false LSP- 3.875,1.542 4.396,2.063 0.521,0.521 10 false LSP+ 2.594,2.896 3.115,3.417 0.521,0.521 10 false E 4.594,2.115 5.125,2.625 0.531,0.51 10 false A 3.49,3.333 4.031,3.615 0.542,0.281 10 false LSP+ 2.76,3.333 3.302,3.615 0.542,0.281 10 false LSP- 4.333,2.115 4.865,2.625 0.531,0.51 10 false B 3.906,2.115 4.438,2.625 0.531,0.51 10 false C 3.781,2.115 4.313,2.625 0.531,0.51 10 false D 3.104,2.115 3.635,2.625 0.531,0.51 10 false E 2.844,2.115 3.375,2.625 0.531,0.51 10 false F 2.417,2.115 2.948,2.625 0.531,0.51 10 false G 2.146,2.115 2.677,2.625 0.531,0.51 10 false H
*1 Seat Position Sensor *2 Front Seat Inner Belt Assembly LH
*3 Airbag Sensor Assembly *4 Front Seat No. 3 Wire LH
*5 Floor Wire *6 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat No. 3 Wire LH)



b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E-2 (LSP+) - Body ground Ignition switch ON Below 1 V
E-1 (LSP-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-2 (LSP+) - E-1 (LSP-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-2 (LSP+) - E-1 (LSP-) Always 1 MΩ or higher
E-2 (LSP+) - Body ground Always 1 MΩ or higher
E-1 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT NO. 3 WIRE LH

NG

7.CHECK FLOOR WIRE
7.CHECK FLOOR WIRE
a.

Disconnect the floor wire connector from the front seat inner belt assembly LH.

B474708C01
3.656,0.802 4.031,1.042 0.375,0.24 2.719,2.938 3.094,3.177 0.375,0.24 4.063,1.521 4.406,1.198 false 4.448,1.625 4.448,1.51 false 4.792,1.521 4.49,1.198 false 2.604,2.167 2.604,1.583 2.604,1.583 2.438,1.583 false 3.219,3.385 3.448,3.115 false 3.781,3.385 3.594,3.115 false 4.573,2.896 4.219,2.219 false 1.885,2.104 2.354,2.51 0.469,0.406 10 false *1 3.354,2.115 3.854,2.521 0.5,0.406 10 false *2 4.917,2.333 5.406,2.833 0.49,0.5 10 false *3 2.292,1.51 2.833,2 0.542,0.49 10 false *4 4.521,2.906 4.917,3.208 0.396,0.302 10 false *5 4.375,1.625 4.802,1.969 0.427,0.344 10 false *6 3.563,0.24 4.083,0.75 0.521,0.51 10 false *a 2.521,2.656 2.958,2.958 0.438,0.302 10 false *b 2.792,2.969 3.229,3.271 0.438,0.302 10 false R69 3.719,0.844 4.156,1.146 0.438,0.302 10 false R32 4.688,1.521 5.26,1.906 0.573,0.385 10 false LSP- 3.927,1.521 4.5,1.906 0.573,0.385 10 false LSP+ 3.073,3.385 3.646,3.771 0.573,0.385 10 false LSP- 3.688,3.385 4.26,3.771 0.573,0.385 10 false LSP+ 4.656,2.115 5.146,2.615 0.49,0.5 10 false A 4.396,2.115 4.885,2.615 0.49,0.5 10 false B 3.969,2.115 4.458,2.615 0.49,0.5 10 false C 3.708,2.115 4.198,2.615 0.49,0.5 10 false D 3.042,2.115 3.531,2.615 0.49,0.5 10 false E 2.781,2.115 3.271,2.615 0.49,0.5 10 false F 2.344,2.115 2.833,2.615 0.49,0.5 10 false G 2.083,2.115 2.573,2.615 0.49,0.5 10 false H
*1 Seat Position Sensor *2 Front Seat Inner Belt Assembly LH
*3 Airbag Sensor Assembly *4 Front Seat No. 3 Wire LH
*5 Floor Wire *6 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)



b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R69-4 (LSP+) - Body ground Ignition switch ON Below 1 V
R69-3 (LSP-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R69-4 (LSP+) - R69-3 (LSP-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R69-4 (LSP+) - R69-3 (LSP-) Always 1 MΩ or higher
R69-4 (LSP+) - Body ground Always 1 MΩ or higher
R69-3 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPLACE FLOOR WIRE