Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327338 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1656  Seat Belt Buckle Switch (LH)  


DESCRIPTION

The front seat belt buckle switch LH circuit consists of the airbag sensor assembly and front seat belt buckle switch LH (front seat inner belt assembly LH).

DTC B1656 is stored when a malfunction is detected in the front seat belt buckle switch LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1656 Seat Belt Buckle Switch (LH)
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front seat belt buckle switch LH circuit.

·

Front seat belt buckle switch LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat belt buckle switch LH (Front seat inner belt assembly LH)

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

WIRING DIAGRAM

B474759E06
5.01,3.083 6.76,3.531 1.75,0.448 10 false Airbag Sensor Assembly 5,2.917 6.323,3.365 1.323,0.448 10 false R32 5.052,1.083 6.375,1.531 1.323,0.448 10 false LBE+ 5.052,1.99 6.375,2.438 1.323,0.448 10 false LBE- 4.792,1.083 6.115,1.531 1.323,0.448 10 false 28 4.792,1.99 6.115,2.438 1.323,0.448 10 false 27 2.292,1.083 3.615,1.531 1.323,0.448 10 false 2 2.292,1.979 3.615,2.427 1.323,0.448 10 false 1 1.854,1.083 3.177,1.531 1.323,0.448 10 false LBE+ 1.875,1.99 3.198,2.438 1.323,0.448 10 false LBE- 0.708,2.531 2.031,2.979 1.323,0.448 10 false R69 0.708,2.708 3.021,3.135 2.313,0.427 10 false Front Seat Belt Buckle Switch LH (Front Seat Inner Belt Assembly LH)

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly LH.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly LH.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE OR FRONT SEAT INNER BELT ASSEMBLY LH

3.CHECK FLOOR WIRE
a.
B474760C01
0.823,0.844 1.177,1.083 0.354,0.24 1.01,3.781 1.344,3.99 0.333,0.208 1.479,2.833 1.479,2.417 false 1.844,1.813 1.844,1.698 false 1.458,1.708 1.781,1.323 false 2.198,1.708 1.896,1.323 false 2.375,4.292 2.031,3.833 false 1.51,4.302 1.854,3.833 false 0.417,2.292 0.802,2.688 0.385,0.396 10 false *1 2.573,2.604 2.969,2.958 0.396,0.354 10 false *2 1.406,2.844 1.792,3.188 0.385,0.344 10 false *3 1.781,1.813 2.177,2.135 0.396,0.323 10 false *4 0.583,0.167 0.979,0.49 0.396,0.323 10 false *a 0.594,3.406 0.958,3.813 0.365,0.406 10 false *b 2.167,2.302 2.563,2.656 0.396,0.354 10 false A 1.75,2.302 2.146,2.656 0.396,0.354 10 false B 1.115,2.302 1.51,2.656 0.396,0.354 10 false C 0.688,2.302 1.083,2.656 0.396,0.354 10 false D 0.875,0.885 1.26,1.281 0.385,0.396 10 false R32 1.052,3.802 1.438,4.198 0.385,0.396 10 false R69 1.323,1.708 1.719,2.031 0.396,0.323 10 false LBE- 2.083,1.708 2.479,2.031 0.396,0.323 10 false LBE+ 2.26,4.313 2.667,4.573 0.406,0.26 10 false LBE+ 1.365,4.313 1.771,4.573 0.406,0.26 10 false LBE-
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R69-2 (LBE+) - Body ground Ignition switch ON Below 1 V
R69-1 (LBE-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 28 (LBE+) and 27 (LBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R69-2 (LBE+) - R69-1 (LBE-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R69-2 (LBE+) - R69-1 (LBE-) Always 1 MΩ or higher
R69-2 (LBE+) - Body ground Always 1 MΩ or higher
R69-1 (LBE-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and front seat inner belt assembly LH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

5.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
5.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Replace the front seat inner belt assembly LH with a known good one.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.



j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



l.

Restore the front seat inner belt assembly LH that was installed for testing to its original location.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG