Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › 2017.09–2017.12
RM33A0E _55 Steering _065371 STEERING COLUMN _0327257 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45250 2.INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


b.

Connect each connector and engage each wire harness clamp to the steering column assembly.


Hide 45220 3.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C384401C01
0.615,0.469 1.625,0.469 true 0.917,0.469 0.917,0.542 0.917,0.542 1.604,0.542 true 0.448,0.385 0.604,0.552 0.156,0.167 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.


b.

Install the steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


d.
C375250

Tighten the clamp.


Hide 45253 4.INSTALL STEERING COLUMN HOLE COVER

a.

Install the steering column hole cover with the 2 clips.


b.

Install the clip.


c.

Return the floor carpet.


Hide 45220 5.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 6.INSTALL FRONT WHEEL LH (for LHD)

Hide 7.INSTALL FRONT WHEEL RH (for RHD)

Hide 87211 8.INSTALL NO. 1 AIR DUCT (for LHD)

a.
C373452

Engage the 3 claws to install a new No. 1 air duct.


b.

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87211 9.INSTALL NO. 1 AIR DUCT (for RHD)

a.
C378533

Engage the 3 claws to install a new No. 1 air duct.


b.

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 73900 10.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 11.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.
C375251C01
1.146,0.542 1.427,0.542 false 0.99,0.448 1.302,0.604 0.313,0.156 10 false *a
*a Clamp


Using pliers, expand the clamp.


b.

While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.


c.

Return the clamp to its original position.


d.

Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 12.INSTALL UPPER STEERING COLUMN COVER

a.
C379359

Engage the 2 claws and 4 clips to connect the upper steering column cover.


b.
C384404C01
0,0 0,0 false
V113147

Install in this direction


Engage the claw to install the upper steering column cover.


Hide 45024 13.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

a.
C384405

Engage the 2 claws to install the lower steering column cover sub-assembly.


b.
C379356

Install the 3 screws.


Hide 14.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84306 15.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 16.INSTALL STEERING WHEEL ASSEMBLY

Hide 17.CHECK STEERING WHEEL CENTER POINT

Hide 45130 18.INSTALL HORN BUTTON ASSEMBLY

Hide 19. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

a.

Set the auto tilt away function setting to the previous condition by changing the customize parameter.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS


Hide 20. PERFORM INITIALIZATION AND CALIBRATION (w/ Parking Assist Monitor System)