Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › 2017.09–2018.04
RM33A0E _59 Vehicle Exterior _065393 MIRROR (EXT) _0327399 POWER MIRROR CONTROL SYSTEM(w/ Memory) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)


B343031N42
4.427,0.167 4.802,0.417 0.375,0.25 2.417,0.167 2.792,0.417 0.375,0.25 4.521,0.208 4.979,0.406 0.458,0.198 10 false N9 2.49,0.208 2.948,0.406 0.458,0.198 10 false N10

a.

Disconnect the N9 outer mirror control ECU assembly (driver door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N9-14 (BDR) - Body ground GR - Body ground +B power supply Always 11 to 14 V
N9-6 (CPUB) - Body ground LA-L - Body ground +B power supply Always 11 to 14 V
N9-5 (SIG) - Body ground LA-B - Body ground Ignition power supply Engine switch off → on (IG) Below 1 V → 11 to 14 V
N9-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the N9 outer mirror control ECU assembly (driver door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N10-1 (RMVR) - N10-10 (RM+R) BR - V Vertical mirror motor drive voltage Driver door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
N10-10 (RM+R) - N10-1 (RMVR) V - BR Vertical mirror motor drive voltage Driver door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
N10-10 (RM+R) - N10-9 (RMHR) V - LG Horizontal mirror motor drive voltage Driver door mirror surface moving right → stopped 11 to 14 V → Below 1 V
N10-9 (RMHR) - N10-10 (RM+R) LG - V Horizontal mirror motor drive voltage Driver door mirror surface moving left → stopped 11 to 14 V → Below 1 V
N10-5 (RVC) - N10-14 (RE1) G - BR Mirror position sensor power supply Engine switch on (IG) 4.55 to 5.45 V
Engine switch off Below 1 V
N10-6 (VSSR) - N9-7 (GND) V - W-B Mirror position sensor signal Engine switch on (IG) 0 to 5 V
N10-13 (HSSR) - N9-7 (GND) GR - W-B Mirror position sensor signal Engine switch on (IG) 0 to 5 V
N9-3 (M2) - N9-7 (GND) R - W-B M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
N9-2 (M1) - N9-7 (GND) BR - W-B M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
N9-1 (MM) - N9-7 (GND) GR - W-B SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)


B343031N43
4.427,0.167 4.802,0.417 0.375,0.25 2.417,0.167 2.792,0.417 0.375,0.25 4.521,0.208 4.979,0.406 0.458,0.198 10 false O8 2.51,0.208 2.969,0.406 0.458,0.198 10 false O9

a.

Disconnect the O8 outer mirror control ECU assembly (front passenger door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O8-14 (BDR) - Body ground GR - Body ground +B power supply Always 11 to 14 V
O8-6 (CPUB) - Body ground LA-L - Body ground +B power supply Always 11 to 14 V
O8-5 (SIG) - Body ground LA-B - Body ground Ignition power supply Engine switch off → on (IG) Below 1 V → 11 to 14 V
O8-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the O8 outer mirror control ECU assembly (front passenger door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O9-1 (LMVR) - O9-10 (LM+R) BR - V Vertical mirror motor drive voltage Front passenger door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
O9-10 (LM+R) - O9-1 (LMVR) V - BR Vertical mirror motor drive voltage Front passenger door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
O9-10 (LM+R) - O9-9 (LMHR) V - LG Horizontal mirror motor drive voltage Front passenger door mirror surface moving right → stopped 11 to 14 V → Below 1 V
O9-9 (LMHR) - O9-10 (LM+R) LG - V Horizontal mirror motor drive voltage Front passenger door mirror surface moving left → stopped 11 to 14 V → Below 1 V
O9-5 (LVC) - O9-14 (LE1) G - BR Mirror position sensor power supply Engine switch on (IG) 4.55 to 5.45 V
Engine switch off Below 1 V
O9-6 (VSSR) - O8-7 (GND) V - W-B Mirror position sensor signal Engine switch on (IG) 0 to 5 V
O9-13 (HSSR) - O8-7 (GND) GR - W-B Mirror position sensor signal Engine switch on (IG) 0 to 5 V



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B472410N19
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.292,6.198 5.729,6.448 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 3.469,7.698 3.781,7.896 0.313,0.198 10 false MB 4.292,0.24 4.604,0.438 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false K51 2.052,1.479 2.365,1.677 0.313,0.198 10 false K52 2.052,1.802 2.365,2 0.313,0.198 10 false K53 0.875,1.083 1.188,1.281 0.313,0.198 10 false 3D 0.875,1.667 1.188,1.865 0.313,0.198 10 false 3C 0.885,2.031 1.198,2.229 0.313,0.198 10 false 3E 0.906,2.26 1.219,2.458 0.313,0.198 10 false 3G 5.854,1.146 6.167,1.344 0.313,0.198 10 false 3B 5.854,1.76 6.167,1.958 0.313,0.198 10 false 3A 1.219,3.302 1.531,3.5 0.313,0.198 10 false K53 3.25,3.271 3.563,3.469 0.313,0.198 10 false K52 5.542,3.26 5.854,3.458 0.313,0.198 10 false K51 1.844,4.625 2.156,4.823 0.313,0.198 10 false 3A 1.229,6.219 1.542,6.417 0.313,0.198 10 false 3C 3.792,6.167 4.104,6.365 0.313,0.198 10 false 3D 5.427,6.25 5.74,6.448 0.313,0.198 10 false 3G 6.448,6.25 6.76,6.448 0.313,0.198 10 false 3E 5.51,4.625 5.823,4.823 0.313,0.198 10 false 3B

a.

Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-31 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
MB-30 (ACC) - Body ground - Ignition power supply (ACC signal) Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω


d.

Connect the main body ECU (multiplex network body ECU) connectors.


e.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
K51-7 (MIRB) - K51-9 (MIRE) L - W Mirror surface adjust switch signal
·

Engine switch on (ACC)

·

Mirror surface adjust switch up


Below 1.7 V
·

Engine switch on (ACC)

·

Mirror surface adjust switch right


Below 2.7 V
·

Engine switch on (ACC)

·

Mirror surface adjust switch down


Below 3.5 V
·

Engine switch on (ACC)

·

Mirror surface adjust switch left


Below 4 V
·

Engine switch on (ACC)

·

Mirror surface adjust switch off


3.8 to 5 V
K51-8 (MIRS) - K51-9 (MIRE) GR - W Mirror select switch signal
·

Engine switch on (ACC)

·

Mirror select switch L


Below 2 V
·

Engine switch on (ACC)

·

Mirror select switch R


Below 1 V
·

Engine switch on (ACC)

·

Mirror select switch off


3.8 to 5.0 V