Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2017.09–2017.12
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 5 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly RH

·

Outer mirror control ECU assembly (for driver side)

(w/ Seat Position Memory System)

·

Outer mirror control ECU assembly (for front passenger side)

(w/ Seat Position Memory System)

·

Position control ECU assembly RH

(w/ Seat Position Memory System)

·

Multiplex tilt and telescopic ECU

(w/ Power Tilt and Power Telescopic System)

·

Air conditioning amplifier assembly

·

Certification ECU (smart key ECU assembly)

(w/ Smart Entry and Start System)

·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Meter mirror sub-assembly

(w/ Headup Display System)

·

No. 3 CAN junction connector

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 5 junction connector

(for RHD)

·

No. 6 junction connector

(for LHD)



WIRING DIAGRAM

C382086E01
0.063,1.375 0.521,1.573 0.458,0.198 10 false K76 0.365,1.375 2.396,1.781 2.031,0.406 10 false Central Gateway ECU (Network Gateway ECU) 0.417,0.688 0.875,0.885 0.458,0.198 10 false 120 Ω 0.948,0.354 1.406,0.552 0.458,0.198 10 false CA5H 0.969,0.885 1.427,1.083 0.458,0.198 10 false CA5L 1.438,0.854 1.896,1.052 0.458,0.198 10 false 16 1.448,0.323 1.906,0.521 0.458,0.198 10 false 15 3.052,0.333 3.51,0.531 0.458,0.198 10 false 1 3,0.854 3.458,1.052 0.458,0.198 10 false 12 3.01,2.74 3.469,2.938 0.458,0.198 10 false 16 3.052,2.198 3.51,2.396 0.458,0.198 10 false 5 1.302,2.208 1.76,2.406 0.458,0.198 10 false 24 1.302,2.74 1.76,2.938 0.458,0.198 10 false 23 0.729,2.854 1.188,3.052 0.458,0.198 10 false CANL 0.729,2.323 1.188,2.521 0.458,0.198 10 false CANH 4.083,2.208 4.542,2.406 0.458,0.198 10 false 2 4.042,2.74 4.5,2.938 0.458,0.198 10 false 13 4.073,0.854 4.531,1.052 0.458,0.198 10 false 14 4.104,0.323 4.563,0.521 0.458,0.198 10 false 3 5.74,0.854 6.198,1.052 0.458,0.198 10 false 8 6.021,0.969 6.479,1.167 0.458,0.198 10 false CANN 6.021,0.438 6.479,0.635 0.458,0.198 10 false CANP 5.729,0.323 6.188,0.521 0.458,0.198 10 false 9 0.333,8.031 2.563,8.677 2.229,0.646 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side)*1 4.646,1.385 5.104,1.583 0.458,0.198 10 false N9 2.917,3.167 3.375,3.365 0.458,0.198 10 false R97 3.229,3.167 5.167,3.49 1.938,0.323 10 false No. 2 Junction Connector 0.063,3.281 0.521,3.479 0.458,0.198 10 false A11 0.365,3.292 2.438,3.813 2.073,0.521 10 false Headlight ECU Sub-assembly RH 4.073,3.635 4.531,3.833 0.458,0.198 10 false 1*3 4.042,4.01 4.5,4.208 0.458,0.198 10 false 16*2 4.083,4.5 4.542,4.698 0.458,0.198 10 false 2*3 4.052,5.01 4.51,5.208 0.458,0.198 10 false 13*3 2.896,5 3.354,5.198 0.458,0.198 10 false 18*2 2.958,4.469 3.417,4.667 0.458,0.198 10 false 7*2 2.74,5.677 3.198,5.875 0.458,0.198 10 false R101 3.135,5.677 4.938,5.938 1.802,0.26 10 false No. 6 Junction Connector*3 1.302,5 1.76,5.198 0.458,0.198 10 false 14 1.292,4.469 1.75,4.667 0.458,0.198 10 false 13 0.75,4.583 1.208,4.781 0.458,0.198 10 false CANP 0.74,5.115 1.198,5.313 0.458,0.198 10 false CANN 0.073,5.552 0.531,5.75 0.458,0.198 10 false a12 0.396,5.552 1.75,5.99 1.354,0.438 10 false Position Control ECU Assembly RH*1 4.083,6.115 4.542,6.313 0.458,0.198 10 false 4 4.042,6.646 4.5,6.844 0.458,0.198 10 false 15 4.073,7 4.531,7.198 0.458,0.198 10 false 3 4.042,7.531 4.5,7.729 0.458,0.198 10 false 14 3,7.521 3.458,7.719 0.458,0.198 10 false 12 3.052,7.01 3.51,7.208 0.458,0.198 10 false 1 2.896,7.969 3.354,8.167 0.458,0.198 10 false R94 3.219,7.969 4.948,8.208 1.729,0.24 10 false No. 1 Junction Connector 1.323,7.521 1.781,7.719 0.458,0.198 10 false 8 1.323,7 1.781,7.198 0.458,0.198 10 false 9 0.74,7.125 1.198,7.323 0.458,0.198 10 false CANP 0.74,7.667 1.198,7.865 0.458,0.198 10 false CANN 0.073,8.031 0.531,8.229 0.458,0.198 10 false O8 4.896,1.385 7.135,1.833 2.24,0.448 10 false Outer Mirror Control ECU Assembly (for Driver Side)*1 5.281,6.073 7.094,6.469 1.813,0.396 10 false *1: w/ Seat Position Memory System 4.073,3.49 4.531,3.688 0.458,0.198 10 false 5*2 4.042,4.156 4.5,4.354 0.458,0.198 10 false 12*3 4.083,4.365 4.542,4.563 0.458,0.198 10 false 6*2 4.052,4.865 4.51,5.063 0.458,0.198 10 false 17*2 3.135,5.406 4.938,5.667 1.802,0.26 10 false No. 5 Junction Connector*2 2.74,5.406 3.198,5.604 0.458,0.198 10 false R100 5.281,6.76 7.094,7.156 1.813,0.396 10 false *2: for RHD 5.281,7.073 7.094,7.469 1.813,0.396 10 false *3: for LHD

C382087E01
0.844,0.469 1.302,0.667 0.458,0.198 10 false MPX1 0.833,0.99 1.292,1.188 0.458,0.198 10 false MPX2 1.396,0.354 1.854,0.552 0.458,0.198 10 false 12 1.396,0.885 1.854,1.083 0.458,0.198 10 false 13 0.156,1.438 0.615,1.635 0.458,0.198 10 false p1 0.406,1.438 2.563,1.771 2.156,0.333 10 false Meter Mirror Sub-assembly*1 3.052,0.896 3.51,1.094 0.458,0.198 10 false 20 3.104,0.354 3.563,0.552 0.458,0.198 10 false 9 4.135,0.354 4.594,0.552 0.458,0.198 10 false 3 4.115,0.896 4.573,1.094 0.458,0.198 10 false 14 4.135,4.125 4.594,4.323 0.458,0.198 10 false 7 4.115,4.656 4.573,4.854 0.458,0.198 10 false 18 5.625,4.646 6.083,4.844 0.458,0.198 10 false 12 5.625,4.125 6.083,4.323 0.458,0.198 10 false 11 5.979,4.25 6.438,4.448 0.458,0.198 10 false CANH 5.99,4.771 6.448,4.969 0.458,0.198 10 false CANL 5.188,5.177 5.646,5.375 0.458,0.198 10 false K54 5.542,5.177 7.094,5.688 1.552,0.51 10 false Air Conditioning Amplifier Assembly 3.063,4.656 3.521,4.854 0.458,0.198 10 false 15 3.104,4.125 3.563,4.323 0.458,0.198 10 false 4 1.396,4.125 1.854,4.323 0.458,0.198 10 false 1 1.406,4.656 1.865,4.854 0.458,0.198 10 false 2 0.833,4.771 1.292,4.969 0.458,0.198 10 false CANL 0.813,4.24 1.271,4.438 0.458,0.198 10 false CANH 0.083,5.198 0.542,5.396 0.458,0.198 10 false K62 0.396,5.198 2.24,5.604 1.844,0.406 10 false Certification ECU (Smart Key ECU Assembly)*3 5.781,6.104 6.24,6.302 0.458,0.198 10 false CANH 5.469,6.083 5.927,6.281 0.458,0.198 10 false 32 5.479,6.625 5.938,6.823 0.458,0.198 10 false 31 5.771,6.635 6.229,6.833 0.458,0.198 10 false CANL 5.406,7.177 5.865,7.375 0.458,0.198 10 false K21 5.74,7.167 6.979,7.583 1.24,0.417 10 false Combination Meter Assembly 4.104,6.625 4.563,6.823 0.458,0.198 10 false 16 4.125,6.083 4.583,6.281 0.458,0.198 10 false 5 3.052,6.625 3.51,6.823 0.458,0.198 10 false 17 3.094,6.083 3.552,6.281 0.458,0.198 10 false 6 1.417,6.083 1.875,6.281 0.458,0.198 10 false 5 1.417,6.625 1.875,6.823 0.458,0.198 10 false 4 0.844,6.729 1.302,6.927 0.458,0.198 10 false CANL 0.823,6.188 1.281,6.385 0.458,0.198 10 false CANH 0.073,7.167 0.531,7.365 0.458,0.198 10 false K52 0.396,7.167 2.052,7.625 1.656,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 2.844,7.115 3.302,7.313 0.458,0.198 10 false K126 3.281,7.115 5.427,7.531 2.146,0.417 10 false No. 3 CAN Junction Connector 3.125,2.24 3.583,2.438 0.458,0.198 10 false 8 3.052,2.771 3.51,2.969 0.458,0.198 10 false 19 1.385,2.76 1.844,2.958 0.458,0.198 10 false 23 1.396,2.229 1.854,2.427 0.458,0.198 10 false 24 0.823,2.344 1.281,2.542 0.458,0.198 10 false CANH 0.844,2.875 1.302,3.073 0.458,0.198 10 false CANL 0.094,3.313 0.552,3.51 0.458,0.198 10 false A10 0.406,3.313 2.771,3.74 2.365,0.427 10 false Headlight ECU Sub-assembly LH 4.115,2.771 4.573,2.969 0.458,0.198 10 false 21 4.104,2.229 4.563,2.427 0.458,0.198 10 false 10 5.688,2.229 6.146,2.427 0.458,0.198 10 false 3 5.646,2.76 6.104,2.958 0.458,0.198 10 false 11 6,2.875 6.458,3.073 0.458,0.198 10 false CANN 5.99,2.354 6.448,2.552 0.458,0.198 10 false CANP 4.979,3.292 5.438,3.49 0.458,0.198 10 false K72 5.323,3.292 7.125,3.771 1.802,0.479 10 false Multiplex Tilt and Telescopic ECU*2 6.292,6.448 6.75,6.646 0.458,0.198 10 false 120 Ω 3.99,7.854 6.135,8.271 2.146,0.417 10 false *1: w/ Headup Display System 3.979,8.49 6.823,8.781 2.844,0.292 10 false *3: w/ Smart Entry and Start System 3.979,8.177 7.031,8.563 3.052,0.385 10 false *2: w/ Power Tilt and Power Telescopic System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the K126 No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C372663C89
3.542,1.365 3.938,1.563 0.396,0.198 0.271,1.354 0.729,1.594 0.458,0.24 2.219,1.719 2.219,2.615 2.219,2.615 2.385,2.615 true 5.948,1.729 5.948,2.146 5.948,2.146 6.115,2.146 true 1.552,1.708 1.552,2.104 1.552,2.104 1.385,2.104 true 2.219,1.417 2.219,0.198 2.219,0.198 2.385,0.198 true 1.552,1.417 1.552,0.729 1.552,0.729 1.385,0.729 true 1.719,1.427 1.719,0.563 1.719,0.563 1.552,0.563 true 1.719,1.708 1.719,2.281 1.719,2.281 1.552,2.281 true 1.885,1.427 1.885,0.375 1.885,0.375 1.719,0.375 true 1.875,1.708 1.875,2.438 1.875,2.438 1.708,2.438 true 2.385,1.708 2.385,2.448 2.385,2.448 2.552,2.448 true 2.563,1.708 2.563,2.281 2.563,2.281 2.729,2.281 true 2.708,1.708 2.708,2.104 2.708,2.104 2.875,2.104 true 2.052,1.719 2.052,2.615 2.052,2.615 1.885,2.615 true 2.052,1.427 2.052,0.198 2.052,0.198 1.885,0.198 true 2.385,1.417 2.385,0.406 2.385,0.406 2.552,0.406 true 2.552,1.417 2.552,0.594 2.552,0.594 2.719,0.594 true 2.729,1.417 2.729,0.76 2.729,0.76 2.896,0.76 true 0.292,0.302 0.604,0.5 0.313,0.198 10 false *a 3.854,0.333 4.167,0.531 0.313,0.198 10 false *1 0.344,1.385 0.74,1.583 0.396,0.198 10 false K126 3.635,1.385 4.031,1.583 0.396,0.198 10 false K68 6.208,2.052 6.604,2.25 0.396,0.198 10 false BAT 0.813,0.646 1.458,0.896 0.646,0.25 10 false CANH*b 2.458,0.125 3.104,0.375 0.646,0.25 10 false CANH*f 0.833,2.031 1.479,2.281 0.646,0.25 10 false CANL*b 2.479,2.531 3.156,2.719 0.677,0.188 10 false CANL*f 0.979,0.479 1.625,0.729 0.646,0.25 10 false CANH*c 1,2.198 1.646,2.448 0.646,0.25 10 false CANL*c 1.313,2.531 1.938,2.729 0.625,0.198 10 false CANL*e 1.333,0.135 1.979,0.385 0.646,0.25 10 false CANH*e 1.146,0.302 1.792,0.552 0.646,0.25 10 false CANH*d 1.146,2.365 1.792,2.531 0.646,0.167 10 false CANL*d 2.635,2.365 3.281,2.615 0.646,0.25 10 false CANL*g 2.802,2.198 3.448,2.448 0.646,0.25 10 false CANL*h 2.958,2.031 3.604,2.281 0.646,0.25 10 false CANL*i 2.635,0.323 3.281,0.573 0.646,0.25 10 false CANH*g 2.813,0.51 3.458,0.76 0.646,0.25 10 false CANH*h 2.99,0.677 3.635,0.927 0.646,0.25 10 false CANH*i
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 1 Junction Connector
*c to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System)
*d to Combination Meter Assembly
*e to Main Body ECU (Multiplex Network Body ECU) *f to Air Conditioning Amplifier Assembly
*g to Headlight ECU Sub-assembly LH *h to Meter Mirror Sub-assembly
(w/ Headup Display System)
*i to Multiplex Tilt and Telescopic ECU
(w/ Power Tilt and Power Telescopic System)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K126-3 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 1 junction connector
K126-14 (CANL) - K68-16 (BAT)
K126-4 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Certification ECU (smart key ECU assembly)*1
K126-15 (CANL) - K68-16 (BAT)
K126-5 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter assembly
K126-16 (CANL) - K68-16 (BAT)
K126-6 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Main body ECU (multiplex network body ECU)
K126-17 (CANL) - K68-16 (BAT)
K126-7 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Air conditioning amplifier assembly
K126-18 (CANL) - K68-16 (BAT)
K126-8 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Headlight ECU sub-assembly LH
K126-19 (CANL) - K68-16 (BAT)
K126-9 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Meter mirror sub-assembly*2
K126-20 (CANL) - K68-16 (BAT)
K126-10 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Multiplex tilt and telescopic ECU*3
K126-21 (CANL) - K68-16 (BAT)


·

*1: w/ Smart Entry and Start System

·

*2: w/ Headup Display System

·

*3: w/ Power Tilt and Power Telescopic System



Result:
Result Proceed to
OK A
NG (Line to No. 1 junction connector) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the R94 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C382111C18
3.646,1.219 4.052,1.479 0.406,0.26 0.188,1.229 0.604,1.469 0.417,0.24 6.115,2.229 5.948,2.229 5.948,2.229 5.948,1.729 true 1.219,1.427 1.219,0.677 1.219,0.677 1.052,0.677 true 1.719,1.427 1.719,0.417 1.719,0.417 1.885,0.417 true 1.208,1.708 1.208,2.125 1.208,2.125 1.042,2.125 true 1.552,1.719 1.552,2.385 1.552,2.385 1.385,2.385 true 1.719,1.719 1.719,2.385 1.719,2.385 1.885,2.385 true 1.552,1.417 1.552,0.417 1.552,0.417 1.385,0.417 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 3.865,0.104 4.177,0.302 0.313,0.198 10 false *1 6.198,2.156 6.646,2.438 0.448,0.281 10 false BAT 3.729,1.271 4.042,1.469 0.313,0.198 10 false K68 0.281,1.281 0.698,1.49 0.417,0.208 10 false R94 0.469,0.604 1.073,0.844 0.604,0.24 10 false CANH*b 0.479,2.042 1.083,2.281 0.604,0.24 10 false CANL*b 0.833,2.302 1.438,2.542 0.604,0.24 10 false CANL*c 0.781,0.344 1.385,0.583 0.604,0.24 10 false CANH*c 1.969,0.344 2.75,0.656 0.781,0.313 10 false CANH*d*e 1.969,2.313 2.708,2.583 0.74,0.271 10 false CANL*d*e
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System)
*c to No. 3 CAN Junction Connector *d to No. 5 Junction Connector
(for RHD)
*e to No. 6 Junction Connector
(for LHD)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R94-1 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Outer mirror control ECU assembly (for front passenger side)*1
R94-12 (CANL) - K68-16 (BAT)
R94-3 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 3 CAN junction connector
R94-14 (CANL) - K68-16 (BAT)
R94-4 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 5 junction connector*2
R94-15 (CANL) - K68-16 (BAT)
R94-4 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 6 junction connector*3
R94-15 (CANL) - K68-16 (BAT)


·

*1: w/ Seat Position Memory System

·

*2: for RHD

·

*3: for LHD



Result:
Result Proceed to
OK A
NG (Line to No. 3 CAN junction connector) B
NG (Line to No. 5 junction connector (for RHD)) C
NG (Line to No. 6 junction connector (for LHD)) D
NG (Line to ECU or sensor) E



A

REPLACE NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 JUNCTION CONNECTOR)

D

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 JUNCTION CONNECTOR)

E

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 JUNCTION CONNECTOR)
a.

Disconnect the R100 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C382111C21
3.646,1.219 4.052,1.479 0.406,0.26 0.188,1.229 0.667,1.5 0.479,0.271 6.115,2.229 5.948,2.229 5.948,2.229 5.948,1.729 true 1.885,1.417 1.885,0.667 1.885,0.667 1.719,0.667 true 2.219,1.417 2.219,0.417 2.219,0.417 2.385,0.417 true 1.885,1.719 1.885,2.146 1.885,2.146 1.719,2.146 true 2.052,1.719 2.052,2.385 2.052,2.385 1.885,2.385 true 2.219,1.719 2.219,2.385 2.219,2.385 2.385,2.385 true 2.042,1.417 2.042,0.417 2.042,0.417 1.875,0.417 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 3.865,0.104 4.177,0.302 0.313,0.198 10 false *1 6.188,2.146 6.563,2.365 0.375,0.219 10 false BAT 3.729,1.271 4.042,1.469 0.313,0.198 10 false K68 0.271,1.281 0.688,1.49 0.417,0.208 10 false R100 1.135,0.604 1.74,0.844 0.604,0.24 10 false CANH*b 1.156,2.073 1.76,2.313 0.604,0.24 10 false CANL*b 1.313,2.313 1.917,2.552 0.604,0.24 10 false CANL*c 1.281,0.333 1.885,0.573 0.604,0.24 10 false CANH*c 2.469,0.333 3.073,0.573 0.604,0.24 10 false CANH*d 2.479,2.302 3.083,2.542 0.604,0.24 10 false CANL*d
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 Junction Connector)
*b to No. 2 Junction Connector
*c to No. 1 Junction Connector *d to Position Control ECU Assembly RH
(w/ Seat Position Memory System)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R100-5 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 2 junction connector
R100-16 (CANL) - K68-16 (BAT)
R100-6 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 1 junction connector
R100-17 (CANL) - K68-16 (BAT)
R100-7 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Position control ECU assembly RH*
R100-18 (CANL) - K68-16 (BAT)


*: w/ Seat Position Memory System



Result:
Result Proceed to
OK A
NG (Line to No. 1 junction connector) B
NG (Line to No. 2 junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR)

D

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
4.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the R101 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C382111C23
3.646,1.219 4.052,1.479 0.406,0.26 0.188,1.229 0.667,1.5 0.479,0.271 6.115,2.229 5.948,2.229 5.948,2.229 5.948,1.729 true 1.208,1.417 1.208,0.667 1.208,0.667 1.042,0.667 true 1.208,1.719 1.208,2.146 1.208,2.146 1.042,2.146 true 1.385,1.719 1.385,2.385 1.385,2.385 1.219,2.385 true 1.385,1.417 1.385,0.417 1.385,0.417 1.219,0.417 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 3.865,0.104 4.177,0.302 0.313,0.198 10 false *1 6.188,2.146 6.563,2.365 0.375,0.219 10 false BAT 3.729,1.271 4.042,1.469 0.313,0.198 10 false K68 0.271,1.281 0.688,1.49 0.417,0.208 10 false R101 0.458,0.594 1.063,0.833 0.604,0.24 10 false CANH*b 0.49,2.073 1.094,2.313 0.604,0.24 10 false CANL*b 0.667,2.313 1.271,2.552 0.604,0.24 10 false CANL*c 0.635,0.333 1.24,0.573 0.604,0.24 10 false CANH*c
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 Junction Connector)
*b to No. 2 Junction Connector
*c to No. 1 Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R101-1 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 2 junction connector
R101-12 (CANL) - K68-16 (BAT)
R101-2 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 1 junction connector
R101-13 (CANL) - K68-16 (BAT)



Result:
Result Proceed to
OK A
NG (Line to No. 1 junction connector) B
NG (Line to No. 2 junction connector) C



A

REPLACE NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the R97 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C382111C26
3.646,1.219 4.052,1.479 0.406,0.26 0.188,1.229 0.625,1.479 0.438,0.25 6.115,2.229 5.948,2.229 5.948,2.229 5.948,1.729 true 1.208,1.417 1.208,0.667 1.208,0.667 1.042,0.667 true 1.208,1.719 1.208,2.146 1.208,2.146 1.042,2.146 true 1.385,1.708 1.385,2.354 1.385,2.354 1.219,2.354 true 1.385,1.417 1.385,0.458 1.385,0.458 1.219,0.458 true 1.552,1.417 1.552,0.281 1.552,0.281 1.385,0.281 true 1.552,1.719 1.552,2.552 1.552,2.552 1.385,2.552 true 1.885,1.719 1.885,2.552 1.885,2.552 2.052,2.552 true 1.885,1.417 1.885,0.281 1.885,0.281 2.052,0.281 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 3.865,0.104 4.177,0.302 0.313,0.198 10 false *1 6.188,2.146 6.563,2.365 0.375,0.219 10 false BAT 3.729,1.271 4.042,1.469 0.313,0.198 10 false K68 0.271,1.281 0.688,1.49 0.417,0.208 10 false R97 0.458,0.594 1.063,0.833 0.604,0.24 10 false CANH*b 0.49,2.073 1.094,2.313 0.604,0.24 10 false CANL*b 0.521,2.271 1.229,2.51 0.708,0.24 10 false CANL*c*d 0.51,0.385 1.24,0.625 0.729,0.24 10 false CANH*c*d 0.813,0.208 1.542,0.448 0.729,0.24 10 false CANH*e 0.823,2.458 1.531,2.698 0.708,0.24 10 false CANL*e 2.146,2.479 2.854,2.719 0.708,0.24 10 false CANL*f 2.146,0.208 2.875,0.448 0.729,0.24 10 false CANH*f
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to No. 5 Junction Connector
(for RHD)
*d to No. 6 Junction Connector
(for LHD)
*e to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System)
*f to Headlight ECU Sub-assembly RH


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R97-1 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
R97-12 (CANL) - K68-16 (BAT)
R97-2 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 5 junction connector*1
R97-13 (CANL) - K68-16 (BAT)
R97-2 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 6 junction connector*2
R97-13 (CANL) - K68-16 (BAT)
R97-3 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Outer mirror control ECU assembly (for driver side)*3
R97-14 (CANL) - K68-16 (BAT)
R97-5 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Headlight ECU sub-assembly RH
R97-16 (CANL) - K68-16 (BAT)


·

*1: for RHD

·

*2: for LHD

·

*3: w/ Seat Position Memory System



Result:
Result Proceed to
OK A
NG (Line to No. 5 junction connector (for RHD)) B
NG (Line to No. 6 junction connector (for LHD)) C
NG (Line to central gateway ECU (network gateway ECU)) D
NG (Line to ECU or sensor) E



A

REPLACE NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

D

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

E

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
6.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C372663C31
3.542,1.365 3.938,1.563 0.396,0.198 0.271,1.354 0.729,1.594 0.458,0.24 5.948,1.729 5.948,2.146 5.948,2.146 6.115,2.146 true 1.208,1.698 1.208,2.198 1.208,2.198 1.042,2.198 true 1.208,1.427 1.208,0.677 1.208,0.677 1.042,0.677 true 0.292,0.302 0.604,0.5 0.313,0.198 10 false *a 3.854,0.333 4.167,0.531 0.313,0.198 10 false *1 0.354,1.385 0.75,1.583 0.396,0.198 10 false R97 3.635,1.385 4.031,1.583 0.396,0.198 10 false K68 6.208,2.052 6.604,2.25 0.396,0.198 10 false BAT 0.469,0.604 1.115,0.854 0.646,0.25 10 false CANH*b 0.5,2.115 1.146,2.365 0.646,0.25 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
R97-1 (CANH) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R97-12 (CANL) - K68-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C351275C17
1.594,0.198 2.01,0.469 0.417,0.271 4.938,0.292 5.354,0.563 0.417,0.271 1.875,2.49 2.01,2.49 2.01,2.49 2.01,1.406 true 6.021,2.156 5.854,2.156 5.854,2.156 5.854,1.677 true 2.271,2.49 2.104,2.49 2.104,2.49 2.104,1.406 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.698,0.25 2.01,0.448 0.313,0.198 10 false K76 1.49,2.417 2.042,2.615 0.552,0.198 10 false CA5L 6.135,2.083 6.688,2.281 0.552,0.198 10 false BAT 2.365,2.396 2.917,2.594 0.552,0.198 10 false CA5H 5.031,0.344 5.344,0.542 0.313,0.198 10 false K68 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
K76-15 (CA5H) - K68-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
K76-16 (CA5L) - K68-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR