Home › Power Source / Network › NETWORKING › NETWORK GATEWAY ECU › 2017.09–2017.12
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321447 NETWORK GATEWAY ECU A

NETWORKING  NETWORK GATEWAY ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during central gateway ECU (network gateway ECU) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of clearance warning ECU assembly*1 Adjust TOYOTA parking assist-sensor system TOYOTA parking assist-sensor system (Click here)

·

*1: w/ TOYOTA Parking Assist-sensor System


CAUTION:
B394719

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION (for LHD)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for LHD)

for 2AR-FE:

Click hereGeneral>MAINTENANCE>2AR-FE BATTERY>REMOVAL

for A25A-FKS:

Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>REMOVAL

for 2GR-FKS:

Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If an airbag deploys for any reason, it may cause a serious injury.



Hide 55435B 3.REMOVE NO. 1 METER HOOD CLUSTER (for LHD)

Hide 55012A 4.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for LHD)

Hide 55476C 5.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for LHD)

Hide 67913 6.REMOVE FRONT DOOR SCUFF PLATE RH (for LHD)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 7.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for LHD)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 8.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for LHD)

Hide 55317A 9.REMOVE INSTRUMENT SIDE PANEL RH (for LHD)

Hide 55607 10.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 73990 11.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD, w/ Passenger Side Knee Airbag)

Hide 55303B 12.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD, w/o Passenger Side Knee Airbag)

Hide 55303B 13.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD, w/ Passenger Side Knee Airbag)

Hide 82877 14.REMOVE ECU INTEGRATION BOX RH (for LHD, w/ ECU Integration Box RH)

a.

Disconnect each connector.


b.
C386723

Disengage the 2 clamps.


c.

Remove the bolt, nut and ECU integration box RH.


Hide 89111 15.REMOVE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for LHD, w/o ECU Integration Box RH)

a.
C371265

Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Disengage the clamp.


c.
C372468

Remove the nut and central gateway ECU (network gateway ECU).


Hide 89111 16.REMOVE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for LHD, w/ ECU Integration Box RH)

a.
C386724

Disengage the 2 claws and remove the central gateway ECU (network gateway ECU).

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.




Hide 73900 17.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)

Hide 55308B 18.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REMOVAL


Hide 82877 19.REMOVE ECU INTEGRATION BOX RH (for RHD)

a.

Disconnect each connector.


b.
C377921

Disengage the clamp.


c.

Remove the bolt, 2 nuts and ECU integration box RH.


Hide 89111 20.REMOVE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for RHD)

a.
C377923

Disengage the 2 claws and remove the central gateway ECU (network gateway ECU).

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.