Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Headup Display Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Headup Display Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Head Up Display" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Head Up Display" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Head Up Display" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Headup Display Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Meter mirror sub-assembly branch line or connector

·

Power source circuit of meter mirror sub-assembly

·

Meter mirror sub-assembly ground circuit

·

Meter mirror sub-assembly



WIRING DIAGRAM

C380547E02
0.229,1.948 0.667,2.188 0.438,0.24 10 false K126 0.615,1.948 2.75,2.198 2.135,0.25 10 false No. 3 CAN Junction Connector 1.719,1.458 2.031,1.656 0.313,0.198 10 false 20 1.76,0.875 2.073,1.073 0.313,0.198 10 false 9 5.344,0.865 5.656,1.063 0.313,0.198 10 false 12 5.354,1.448 5.667,1.646 0.313,0.198 10 false 13 5.677,0.99 6.365,1.26 0.688,0.271 10 false MPX1 5.677,1.573 6.292,1.906 0.615,0.333 10 false MPX2 5.667,2.469 5.979,2.667 0.313,0.198 10 false B 5.406,2.344 5.719,2.542 0.313,0.198 10 false 2 3.823,2.281 5.021,2.594 1.198,0.313 10 false ECU-DCC NO. 2 2.24,2.448 3.448,2.813 1.208,0.365 10 false from Battery 1.688,3.271 3.427,3.708 1.74,0.438 10 false from IG1-NO. 1 Relay 3.875,3.104 5.146,3.417 1.271,0.313 10 false ECU-IG1 NO. 4 5.396,3.135 5.708,3.333 0.313,0.198 10 false 1 5.677,3.281 5.99,3.479 0.313,0.198 10 false IG 5.417,3.99 5.729,4.188 0.313,0.198 10 false 4 5.667,4.115 5.979,4.313 0.313,0.198 10 false ES 5.083,4.771 5.396,4.969 0.313,0.198 10 false p1 5.323,4.771 7.156,5.198 1.833,0.427 10 false Meter Mirror Sub-assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (METER MIRROR SUB-ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the p1 meter mirror sub-assembly connector.


c.
C381610C02
1.531,0.271 1.906,0.563 0.375,0.292 2.188,1.99 2.188,2.74 2.188,2.74 2.354,2.74 true 2.031,1.979 2.031,2.729 2.031,2.729 1.865,2.729 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.656,0.323 1.969,0.521 0.313,0.198 10 false p1 2.469,2.656 2.927,2.958 0.458,0.302 10 false MPX2 1.396,2.646 1.917,2.875 0.521,0.229 10 false MPX1
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
p1-12 (MPX1) - p1-13 (MPX2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (METER MIRROR SUB-ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C381610C03
1.531,0.271 1.906,0.563 0.375,0.292 2.729,1.635 2.729,0.802 2.729,0.802 2.896,0.802 true 1.01,1.635 1.01,0.802 1.01,0.802 1.177,0.802 true 0.698,1.625 0.698,0.552 0.698,0.552 0.865,0.552 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.656,0.323 1.969,0.521 0.313,0.198 10 false p1 1.271,0.719 1.583,0.917 0.313,0.198 10 false B 2.979,0.719 3.292,0.917 0.313,0.198 10 false ES 0.958,0.469 1.271,0.667 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
p1-4 (ES) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
p1-1 (IG) - Body ground Ignition switch ON 11 to 14 V
p1-2 (B) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)