Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327348 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for an LHD vehicle.



PROCEDURE

Hide 89170 1.INSTALL AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B468739N01
2.563,1.146 2.719,1.344 0.156,0.198 10 true A 0.406,0.74 0.563,0.938 0.156,0.198 10 true B 1.823,0.406 1.979,0.604 0.156,0.198 10 true C

Install the airbag sensor assembly with the 3 bolts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)

NOTICE:
·

Temporarily tighten the 2 bolts in the order of (A), (B) and then fully tighten the 3 bolts in the order of (C), (A) and (B).

·

If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the airbag sensor assembly, make sure that the SRS wiring does not interfere with or is not pinched between other parts.

·

When the ignition switch is first turned to ON after the airbag sensor assembly has been replaced, make sure that no one is in the vehicle.




d.
B468738C01
0.771,2.135 1.031,2.135 1.031,2.135 1.135,2.5 true 0.583,2.031 0.771,2.24 0.188,0.208 10 true *a
*a Lock Lever
V113147

Move in this Direction


Temporarily connect the connector and then move the lock lever in the direction indicated by the arrow to securely connect the connectors.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



e.

Check that there is no looseness in the installed parts of the airbag sensor assembly.


Hide 58861B 2.INSTALL NO. 1 CONSOLE BOX DUCT

a.
C378613C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 1 console box duct with the clip as shown in the illustration.


Hide 58510D 3.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.
E372541

Install the front floor carpet assembly to its original position as shown in the illustration.


b.

Engage the 2 guides.


c.

Install the 2 front floor carpet clips.


d.
E372536

Install the front floor carpet assembly to its original position as shown in the illustration.


e.

Engage the 2 guides.


f.

for LHD:

i.

Install the 2 front floor carpet clips.



g.

for RHD:

i.

Install the front floor carpet clip.



Hide 58569D 4.INSTALL FRONT FLOOR CAUTION PLATE COVER

Hide 55606 7.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 55606 8.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 62414A 9.INSTALL LOWER CENTER PILLAR GARNISH LH

Hide 62332A 10.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67918A 11.INSTALL REAR DOOR SCUFF PLATE LH

Hide 62312B 12.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62112A 13.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 67914 14.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 55607 15.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62413A 16.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 62331A 17.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

Hide 67917A 18.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 62311B 19.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62111A 20.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 67913 21.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 72693 22.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 23.INSTALL REAR SEAT CUSHION ASSEMBLY

Hide 73350C 24.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 58810J 25.INSTALL CONSOLE BOX ASSEMBLY

Hide 27.INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION


Hide 28.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

Hide 30. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION

a.

When the airbag sensor assembly is replaced, perform zero point learning for the yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

HINT:

The yaw rate and acceleration sensor is built into the airbag sensor assembly.