Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR › 2017.09–2018.04
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327352 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 89831B 1.INSTALL SIDE NO. 2 AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296256C01
5.01,0.51 5.302,0.781 0.292,0.271 10 *b 1.792,0.51 2.083,0.802 0.292,0.292 10 *a
*a Correct *b Incorrect



d.

Engage the claw and install the side No. 2 airbag sensor with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the side No. 2 airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the side No. 2 airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the side No. 2 airbag sensor claw is securely inserted into the body hole.




e.

Connect the connector to the side No. 2 airbag sensor.

B474825C01
3.74,1.208 4.188,1.594 true 5.875,1.448 6.323,1.833 true 3.031,0.792 3.479,1.177 true 1.083,0.542 1.531,0.927 true 4.198,1.573 4.51,1.729 0.313,0.156 10 false *a 6.354,1.813 6.667,1.969 0.313,0.156 10 false *a 2.896,0.688 3.104,0.885 0.208,0.198 10 false A 0.948,0.458 1.156,0.656 0.208,0.198 10 false A
*a White Housing Lock - -
V113147

Connect in this Direction - -


NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:
·

Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).

·

When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.




f.

Check that there is no looseness in the installed parts of the side No. 2 airbag sensor.


Hide 2.INSTALL REAR SIDE SEATBACK ASSEMBLY

Hide 62332A 3.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 4.INSTALL REAR SEATBACK ASSEMBLY (for Reclining Seat Type)

Hide 72996A 5.INSTALL REAR SEATBACK COVER (for Reclining Seat Type)

Hide 71940A 6.INSTALL REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

Hide 72693 7.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 8.INSTALL REAR SEAT CUSHION ASSEMBLY

Hide 73350C 9.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

for 2AR-FE: Click hereGeneral>MAINTENANCE>2AR-FE BATTERY>INSTALLATION

for A25A-FKS: Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>INSTALLATION

for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION