Perform the following procedure to troubleshoot the dynamic radar cruise control system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Adjust the reflector height.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Place the reflector.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Turn the cruise control main switch on.
Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.
Check the amount of misalignment and make a note.
| Tester Display |
|---|
| Front Beam Axis Adjustment |
Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.
Check the amount of offset and make a note.
| Tester Display |
|---|
| Front Beam Axis Offset Reading |
Calculate the "Dealership Axis Offset Angle (with On-line Calibration Angle)" using the values "Front Beam Axis Misalignment Reading" and "Front Beam Axis Offset Reading".
"Dealership Axis Offset Angle (with On-line Calibration Angle)" = "Front Beam Axis Misalignment Reading" - "Front Beam Axis Offset Reading"
| Vertical | -5.2 to 5.2 deg. |
| Horizontal | -0.6 to 0.6 deg. |
| Result | Proceed to |
|---|---|
| The dealership axis offset angle (with on-line calibration angle) is within the specified range. | A |
| The dealership axis offset angle (with on-line calibration angle) is not within the specified range. | B |
A
B
Using the GTS, check that the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
CAN communication system is functioning normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
| Result | Proceed to |
|---|---|
| Meter/gauge system DTCs are not output | A |
| Meter/gauge system DTCs are output | B |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
| Result | Proceed to |
|---|---|
| Vehicle stability control system and electric parking brake system DTCs are not output | A |
| Vehicle stability control system DTCs are output | B |
| Electric parking brake system DTCs are output | C |
A
B
C
Check for DTCs and note any codes that are output.
Clear the DTCs.
Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Refer to Problem Symptoms Table.
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Data List / Active Test
Operation check
Terminals of ECU
| Proceed to |
|---|
| NEXT |
NEXT
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT