Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for 2AR-FE) › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0327281 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2AR-FE) D

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2AR-FE)  ROAD TEST  


HINT:

The dynamic radar cruise control system has 2 cruise control modes: constant speed control mode and vehicle-to-vehicle distance control mode.

·

Vehicle-to-vehicle distance control mode is selected by default when the dynamic radar cruise control system is turned on using the cruise control main switch.

·

Operation of constant speed control mode is the same as that for a conventional cruise control system.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 2AR-FE)>ROAD TEST



PROBLEM SYMPTOM CONFIRMATION


a.

Inspect the SET function.

i.
A401983

Turn the dynamic radar cruise control system on using the cruise control main switch.


ii.

Check that the cruise control indicator light illuminates in the combination meter assembly.


iii.

Drive at a speed between approximately 50 km/h (31 mph) and 180 km/h (112 mph).


iv.
A401984

Push the -SET switch.


v.
A305785C14
1.219,0.271 1.531,0.427 0.313,0.156 10 false *a 1.219,1.302 1.531,1.458 0.313,0.156 10 false *b
*a Cruise Control Indicator
(Vehicle-to-vehicle Distance Control Mode)
*b Cruise SET Indicator


Check that the cruise control indicator remains illuminated, the cruise SET indicator illuminates in the combination meter assembly and the set speed is displayed on the multi-information display.


vi.

After releasing the switch, check that the vehicle maintains the set speed.



b.

Inspect the + (ACCEL) function.

i.
A401983

Turn the dynamic radar cruise control system on using the cruise control main switch.


ii.

Drive at a speed between approximately 50 km/h (31 mph) and 180 km/h (112 mph).


iii.
A401984

Push the -SET switch.


iv.
A401985

Check that vehicle speed increases while the +RES switch is pushed, and that the vehicle maintains the newly set speed when the switch is released.


v.

Push the +RES switch and then release it immediately. Check that the vehicle speed increases* (tap-up control).

HINT:

*: Constant speed control mode: increases by approximately 1 km/h or 1 mph; vehicle-to-vehicle distance control mode: increases by approximately 1 km/h or 1 mph.




c.

Inspect the - (COAST) function.

i.
A401983

Turn the dynamic radar cruise control system on using the cruise control main switch.


ii.

Drive at a speed between approximately 50 km/h (31 mph) and 180 km/h (112 mph).


iii.
A401984

Push the -SET switch.


iv.

Check that vehicle speed decreases while the - SET switch is pushed, and the vehicle maintains the newly set speed when the switch is released.


v.

Push the -SET switch, and then release it immediately. Check that the vehicle speed decreases* (tap-down control).

HINT:

*: Constant speed control mode: decreases by approximately 1 km/h or 1 mph; vehicle-to-vehicle distance control mode: decreases by approximately 1 km/h or 1 mph.




d.

Inspect the CANCEL function.

i.
A401983

Turn the dynamic radar cruise control system on using the cruise control main switch.


ii.

Drive at a speed between approximately 50 km/h (31 mph) and 180 km/h (112 mph).


iii.
A401984

Push the -SET switch.


iv.
A401986

When any of the following are performed, check that control of vehicle speed by the dynamic radar cruise control system is canceled and that the normal driving mode (no control of vehicle speed by the dynamic radar cruise control system) resumes.

·

Depressing the brake pedal.

·

Moving the shift lever from D or S to any other position.

·

Selecting the S3, S2 or S1 range with the shift lever in S.

·

Selecting the D3, D2 or D1 range using the transmission shift switch assembly (shift paddle switch) with the shift lever in D (w/ Shift Paddle Switch).

·

Pushing the CANCEL switch.

·

Turning the cruise control system off using the cruise control main switch (the stored vehicle speed in the ECM is not maintained).




e.

Inspect the RES (RESUME) function.

i.
A401983

Turn the dynamic radar cruise control system on using the cruise control main switch.


ii.

Drive at a speed between approximately 50 km/h (31 mph) and 180 km/h (112 mph).


iii.
A401984

Push the -SET switch.


iv.

Cancel control of vehicle speed by the dynamic radar cruise control system by performing any of the CANCEL functions (other than turning the dynamic radar cruise control system off using the cruise control main switch).


v.
A401985

Push the +RES switch while driving the vehicle at a speed of more than approximately 40 km/h (25 mph), and check that the vehicle resumes the speed set prior to cancellation and that the cruise SET indicator illuminates.

HINT:

The stored vehicle speed is retained even if vehicle speed drops below approximately 40 km/h (25 mph). The previously stored vehicle speed can be resumed by pushing the +RES switch when the vehicle speed has returned to approximately 40 km/h (25 mph) or more.





CHECK FULL-SPEED RANGE FOLLOWING FUNCTION


a.

Check the SET function.

i.
A401983

Turn the dynamic radar cruise control system on using the cruise control main switch.


ii.

Drive at a speed between approximately 0 km/h (0 mph) and 180 km/h (112 mph).


iii.

Check that there is a preceding vehicle that can be tracked.

HINT:

Tracking control may not track the preceding vehicle under the following conditions:

·

The rear of the preceding vehicle is small, such as an empty trailer or motorcycle.




iv.
A401984

Push the -SET switch.


v.

Check that tracking of the preceding vehicle begins with the set vehicle speed as the upper limit when the -SET switch is pressed.


vi.

Check that the set vehicle speed is displayed on the multi-information display in the combination meter assembly.



b.

Check the deceleration function.

i.

When the preceding vehicle decelerates, check that the vehicle automatically decelerates while maintaining the set vehicle-to-vehicle distance.


ii.

When the vehicle stops, check that "WAITING" is displayed on the multi-information display in the combination meter assembly.

HINT:

When "WAITING" is displayed on the multi-information display in the combination meter assembly, even if the brake pedal is depressed, tracking control is not canceled.




c.

Check the acceleration function.

i.

When the preceding vehicle starts off, check that "Operate Cruise Switch or Accelerator Pedal to Resume" is displayed on the multi-information display in the combination meter assembly.


ii.
A401985

When the +RES switch is pushed or the accelerator pedal is depressed, check that tracking control resumes and begins tracking the preceding vehicle.



d.

Check the tracking control cancel function.

i.

When the vehicle speed is approximately 40 km/h (25 mph) or less and the preceding vehicle is no longer in front of the vehicle, check that "Radar Cruise Control Not Available No Preceding Vehicle" is displayed on the multi-information display in the combination meter assembly, the warning buzzer sounds 4 times and tracking control cancels.

HINT:

Tracking control also automatically cancels when the preceding vehicle moves out of the detection range due to a curve, etc., when the vehicle speed is 40 km/h (25 mph) or less.