CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the K62 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| K62-18 (E) - Body ground | W-B - Body ground | - | Ground | Always | Below 1 Ω | - |
| K62-4 (+B) - K62-18 (E) | W - W-B | Input | Power supply | Always | 11 to 14 V | - |
| K62-15 (CUTB) - K62-18 (E) | R - W-B | Input | Dark current cut pin* | Always | 11 to 14 V | - |
*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).
Reconnect the K62 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| K62-17 (IG1D) - K62-18 (E) | R - W-B | Output | IG power supply | Engine switch off → on (IG) | Below 1 V → 10 V or higher | Power source control
IG Relay Monitor (Outside) |
| K62-16 (ACCD) - K62-18 (E) | LG - W-B | Output | ACC power supply | Engine switch off → on (ACC) | Below 1 V → 10 V or higher | Power source control
ACC Relay Monitor |
| R8-17 (CLG1) - K62-18 (E) | R - W-B | Output | Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
Pulse generation
(See waveform 1) |
- |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
Pulse generation
(See waveform 2) |
- | ||||
| R8-17 (CLG1) - K62-18 (E) | R - W-B | Input | Input to driver door lock sensor
(front door outside handle assembly (for driver door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly)) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) 5.
Driver door lock sensor touched |
Pulse generation
(See waveform 3) |
- |
| R8-17 (CLG1) - K62-18 (E) | R - W-B | Input | Input to driver door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly)) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not near the vehicle 5.
Driver door unlock sensor touched |
Pulse generation
(See waveform 4) |
- |
| R8-16 (CG1B) - K62-18 (E) | GR - W-B | Output | Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
Pulse generation
(See waveform 5) |
- |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
Pulse generation
(See waveform 6) |
- | ||||
| R8-15 (CLG2) - K62-18 (E) | R - W-B | Output | Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
Pulse generation
(See waveform 1) |
- |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
Pulse generation
(See waveform 2) |
- | ||||
| R8-15 (CLG2) - K62-18 (E) | R - W-B | Input | Input to front passenger door lock sensor
(front door outside handle assembly (for front passenger door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly)) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) 5.
Front passenger door lock sensor touched |
Pulse generation
(See waveform 3) |
- |
| R8-15 (CLG2) - K62-18 (E) | R - W-B | Input | Input to front passenger door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly)) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not near the vehicle 5.
Front passenger door unlock sensor touched |
Pulse generation
(See waveform 4) |
- |
| R8-14 (CG2B) - K62-18 (E) | W - W-B | Output | Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
Pulse generation
(See waveform 5) |
- |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation |
Pulse generation
(See waveform 6) |
- | ||||
| R8-11 (CLG7) - K62-18 (E) | GR - W-B | Output | Output to No. 1 indoor electrical key antenna assembly (inside luggage compartment) | Procedure:
1.
Door is closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Driver door lock sensor touched |
Pulse generation
(See waveform 7) |
- |
| R8-10 (CG7B) - K62-18 (E) | R - W-B | Output | Output to No. 1 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) | Procedure:
1.
Door is closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Driver door lock sensor touched |
Pulse generation
(See waveform 7) |
- |
| R8-13 (CLG8) - K62-18 (E) | G - W-B | Output | Output to electrical key antenna (outside luggage compartment) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Luggage electrical key switch off → on |
Pulse generation
(See waveform 8) |
- |
| R8-12 (CG8B) - K62-18 (E) | L - W-B | Output | Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG8 output terminal) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Luggage electrical key switch off → on |
Pulse generation
(See waveform 8) |
- |
| R8-26 (TSW5) - K62-18 (E) | LG - W-B | Input | Luggage electrical key switch signal input | Luggage electrical key switch off → on | Pulse generation
(See waveform 9) |
Entry&Start
Tr/B-Door Unlock SW |
| R8-18 (RCO) - K62-18 (E) | B - W-B | Output | Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation
(See waveform 10) |
- |
| R8-19 (RDAM) - K62-18 (E) | G - W-B | Input | Door control receiver verifies data received from electrical key transmitter sub-assembly.
Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)). |
Proceed:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation
(See waveform 11) |
- |
| R8-20 (CSEL) - K62-18 (E) | BE - W-B | Output | Communication channel switching circuit | Procedure:
1.
Engine switch off 2.
All doors closed |
Below 1 V → Pulse generation | - |
*: For details about the entry function detection area, refer to Operation Check.
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-17 (CLG1) - K62-18 (E)
R8-15 (CLG2) - K62-18 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
*: For details about the entry function detection area, refer to Operation Check.
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-17 (CLG1) - K62-18 (E)
R8-15 (CLG2) - K62-18 (E) |
| Tool Setting | 5 V/DIV., 100 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
*: For details about the entry function detection area, refer to Operation Check.
| *a | Lock sensor not touched |
| *b | Lock sensor touched |
Using an oscilloscope, check waveform 3.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-17 (CLG1) - K62-18 (E)
R8-15 (CLG2) - K62-18 (E) |
| Tool Setting | 5 V/DIV., 40 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) 5.
Lock sensor not touched → touched |
*: For details about the entry function detection area, refer to Operation Check.
| *a | Unlock sensor not touched |
| *b | Unlock sensor touched |
Using an oscilloscope, check waveform 4.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-17 (CLG1) - K62-18 (E)
R8-15 (CLG2) - K62-18 (E) |
| Tool Setting | 5 V/DIV., 50 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors locked 4.
Electrical key transmitter sub-assembly not near the vehicle 5.
Unlock sensor not touched → touched |
Using an oscilloscope, check waveform 5.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-16 (CG1B) - K62-18 (E)
R8-14 (CG2B) - K62-18 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*) |
*: For details about the entry function detection area, refer to Operation Check.
Using an oscilloscope, check waveform 6.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-16 (CG1B) - K62-18 (E)
R8-14 (CG2B) - K62-18 (E) |
| Tool Setting | 5 V/DIV., 100 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*) |
*: For details about the entry function detection area, refer to Operation Check.
| *a | Driver door lock sensor not touched |
| *b | Driver door lock sensor touched |
Using an oscilloscope, check waveform 7.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-11 (CLG7) - K62-18 (E)
R8-10 (CG7B) - K62-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Door is closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Driver door lock sensor touched |
Using an oscilloscope, check waveform 8.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-13 (CLG8) - K62-18 (E)
R8-12 (CG8B) - K62-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Luggage electrical key switch off → on |
| *a | Checking for switch on signal at short intervals |
Using an oscilloscope, check waveform 9.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-26 (TSW5) - K62-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Luggage electrical key switch off → on |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 10.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-18 (RCO) - K62-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
| *a | Before lock or unlock switch of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 11.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | R8-19 (RDAM) - K62-18 (E) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | for LHD | *B | for RHD |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Input/Output | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|---|
| MB-11 (GND1) - Body ground | - | - | Ground | Always | Below 1 Ω |
| MB-31 (BECU) - Body ground | - | Input | Battery power supply (for CPU) | Always | 11 to 14 V |