Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328237 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

IG Circuit


Starting Control
·

Ignition



WIRING DIAGRAM

B482819E04
0.896,0.76 1.208,0.958 0.313,0.198 10 false IC 1.26,0.427 1.573,0.625 0.313,0.198 10 false +B 1.458,0.813 2.073,1.01 0.615,0.198 10 false IG1D 1.854,0.802 2.167,1 0.313,0.198 10 false 17 0.479,1.427 0.938,1.625 0.458,0.198 10 false K62 3.563,0.708 3.875,0.906 0.313,0.198 10 false 17 3.573,0.906 3.885,1.104 0.313,0.198 10 false 3A 3.615,1.604 3.771,1.802 0.156,0.198 10 false 1 3.573,1.802 3.885,2 0.313,0.198 10 false 3F 3.594,2.969 3.906,3.167 0.313,0.198 10 false 3E 3.604,2.771 3.76,2.969 0.156,0.198 10 false 1 3.583,3.365 3.896,3.563 0.313,0.198 10 false 3C 3.573,3.177 3.885,3.375 0.313,0.198 10 false 13 6.125,0.656 6.438,0.854 0.313,0.198 10 false 3D 6.115,2.958 6.427,3.156 0.313,0.198 10 false 3C 6.115,3.354 6.427,3.552 0.313,0.198 10 false 3B 6.115,0.458 6.427,0.656 0.313,0.198 10 false 35 6.156,1.615 6.313,1.813 0.156,0.198 10 false 2 6.125,2.771 6.438,2.969 0.313,0.198 10 false 15 6.167,3.177 6.323,3.375 0.156,0.198 10 false 3 4.302,1.167 5.531,1.365 1.229,0.198 10 false IG1-NO. 1 4.302,2.323 5.531,2.521 1.229,0.198 10 false IG1-NO. 2 4.313,3.625 5.542,3.823 1.229,0.198 10 false IG2-NO. 2 4.969,0.781 6.198,0.979 1.229,0.198 10 false ECU-IG1 NO. 4 5.156,1.948 6.073,2.146 0.917,0.198 10 false WASHER 4.938,3.094 6.167,3.292 1.229,0.198 10 false ECU-IG2 NO. 3 0.927,3.656 2.156,3.854 1.229,0.198 10 false IG2 NO. 1 1.51,3.26 1.667,3.458 0.156,0.198 10 false 1 0.844,3.26 1,3.458 0.156,0.198 10 false 2 0.844,2.99 1,3.188 0.156,0.198 10 false 3 1.51,3 1.667,3.198 0.156,0.198 10 false 5 0.458,1.583 1.99,2.063 1.531,0.479 10 false Certification ECU (Smart Key ECU Assembly) 3.594,3.896 6.573,4.26 2.979,0.365 10 false Instrument Panel Junction Block Assembly 6.115,1.792 6.427,1.99 0.313,0.198 10 false 3C

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the smart entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Starting Control > Trouble Codes
50001 221

Result:
Result Proceed to
DTCs are not output A
Smart entry and start system (for Start Function) DTCs are output B



A

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B424427C69
1.542,0.083 1.958,0.333 0.417,0.25 0.927,1.979 1.177,1.979 1.177,1.979 1.177,0.979 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.625,0.115 1.979,0.375 0.354,0.26 10 false K62 0.583,1.896 1.083,2.135 0.5,0.24 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K62-17 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 3A, 3B, 3E and 3F instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-17 (IG1D) - 3A-17 Always Below 1 Ω
3B-3 - Body ground Always Below 1 Ω
K62-17 (IG1D) or 3A-17 - Other terminals and body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Always 11 to 14 V
3E-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1-NO. 1, IG1-NO. 2, IG2-NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1-NO. 1, IG1-NO. 2, IG2-NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect all of the instrument panel junction block assembly connectors.


c.

Connect the K62 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

B463118C15
2.26,2.333 2.573,2.542 0.313,0.208 3.698,2.333 4.01,2.542 0.313,0.208 0.083,0.125 0.396,0.281 0.313,0.156 10 false *a 2.344,2.365 2.656,2.521 0.313,0.156 10 false 3D 3.771,2.354 4.083,2.51 0.313,0.156 10 false 3C
*a Component with harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
3D-35 - Body ground Engine switch on (IG) 11 to 14 V
3C-2 - Body ground Engine switch on (IG) 11 to 14 V
3C-15 - Body ground Engine switch on (IG) 11 to 14 V
3C-13 - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IG2 NO. 1 RELAY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IG2 NO. 1 RELAY)
a.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-13 - Engine room relay block and junction block assembly IG2 NO. 1 relay terminal 1 Always Below 1 Ω
Engine room relay block and junction block assembly IG2 NO. 1 relay terminal 2 - Body ground Always Below 1 Ω
3C-13 or engine room relay block and junction block assembly IG2 NO. 1 relay terminal 1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT IG2 NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT IG2 NO. 1 RELAY
a.
C279145C08
2.031,0.625 1.677,0.385 false 2.604,0.677 2.917,0.469 false 2.385,1.135 2.875,1.135 false 2.448,1.635 2.906,1.635 false 0.24,0.667 0.396,0.865 0.156,0.198 10 false 3 1.188,0.677 1.344,0.875 0.156,0.198 10 false 5 0.24,1.198 0.396,1.396 0.156,0.198 10 false 1 1.188,1.219 1.375,1.417 0.188,0.198 10 false 2 1.552,0.26 1.708,0.458 0.156,0.198 10 false 1 2.969,0.344 3.125,0.542 0.156,0.198 10 false 2 2.979,1.073 3.135,1.271 0.156,0.198 10 false 5 3,1.563 3.156,1.76 0.156,0.198 10 false 3 0.125,0.104 0.385,0.313 0.26,0.208 10 false *1
*1 IG2 NO. 1 Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE IG2 NO. 1 RELAY