Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.09–2021.02
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328237 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The certification ECU (smart key ECU assembly) blinks the security indicator light (telltale light assembly)*1 or security indicator light (clock assembly)*2 when the immobiliser is set (engine switch off).

·

The certification ECU (smart key ECU assembly) receives the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is in the arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light (telltale light assembly)*1 or security indicator light (clock assembly)*2.

*1: w/ Telltale Light Assembly

*2: w/ Clock Assembly



WIRING DIAGRAM

B491803E01
0.792,1.01 1.292,1.219 0.5,0.208 10 false E 1.563,1 2.063,1.208 0.5,0.208 10 false LP 0.448,0.75 0.729,1.156 0.281,0.406 10 false 6*1, 7*2 1.875,0.75 2.146,1.208 0.271,0.458 10 false 9*1, 5*2 2.927,0.885 3.427,1.094 0.5,0.208 10 false 20 3.177,0.885 3.677,1.094 0.5,0.208 10 false IND 3.635,0.417 4.135,0.625 0.5,0.208 10 false 12 V 5.302,1.865 6.938,2.281 1.635,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 2.958,1.865 3.458,2.073 0.5,0.208 10 false K62 2.948,2.031 4.479,2.49 1.531,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.385,1.854 1.427,2.094 1.042,0.24 10 false K36*1, K59*2 0.375,2.021 2.302,2.427 1.927,0.406 10 false Security Indicator Light (Telltale Light Assembly)*1 0.615,3.427 2.521,3.667 1.906,0.24 10 false : CAN Communication Line 0.365,2.667 1.792,3.104 1.427,0.438 10 false Security Indicator Light (Clock Assembly)*2 2.948,3.365 4.594,3.792 1.646,0.427 10 false *2: w/ Clock Assembly 2.948,3 4.875,3.406 1.927,0.406 10 false *1: w/ Telltale Light Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Engine > Trouble Codes
50001 372
Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)

NG

2.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Immobiliser Indicator
50004 125 28
OK:

The security indicator light operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK SECURITY INDICATOR LIGHT OPERATION

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT AND BODY GROUND)
3.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light illuminates.*2

OK:

The security indicator light illuminates normally.



Result:
Result Proceed to
*1 is NG (*2 is OK) A
*2 is NG (*1 is OK) B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT AND BODY GROUND)
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K36 security indicator light (telltale light assembly) connector.*1


c.

Disconnect the K59 security indicator light (clock assembly) connector.*2

*1: w/ Telltale Light Assembly

*2: w/ Clock Assembly



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Telltale Light Assembly
Tester Connection Condition Specified Condition
K62-20 (IND) - K36-9 (LP) Always Below 1 Ω
K62-20 (IND) or K36-9 (LP) - Other terminals and body ground Always 10 kΩ or higher
K36-6 (E) - Body ground Always Below 1 Ω

w/ Clock Assembly
Tester Connection Condition Specified Condition
K62-20 (IND) - K59-5 (LP) Always Below 1 Ω
K62-20 (IND) or K59-5 (LP) - Other terminals and body ground Always 10 kΩ or higher
K59-7 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the K62 certification ECU (smart key ECU assembly) connector.


b.

Connect the K36 security indicator light (telltale light assembly) connector.*1


c.

Connect the K59 security indicator light (clock assembly) connector.*2

*1: w/ Telltale Light Assembly

*2: w/ Clock Assembly



d.

Using an oscilloscope, check the waveform.

B416787C30
4.583,0.417 5,0.667 0.417,0.25 5.198,2.302 5.031,2.302 5.031,2.302 5.031,1.427 true 4.667,0.458 4.979,0.656 0.313,0.198 10 false K62 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 5.24,2.208 5.698,2.417 0.458,0.208 10 false IND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Measurement Condition:
Tester Connection Condition Specified Condition
K62-20 (IND) - Body ground Engine switch off → on (IG) Pulse generation → Below 2 V



Result:
Result Proceed to
OK (w/ Telltale Light Assembly) A
OK (w/ Clock Assembly) B
NG C



A

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

B

REPLACE SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)