The main body ECU (multiplex network body ECU) determines the ignition switch position (LOCK, ACC, ON) based on signals from the IG and ACC circuit.
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ACC SW | Ignition switch | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ACC |
- |
| IG SW | Ignition switch | OFF or ON | OFF: Ignition switch off or ACC
ON: Ignition switch ON |
- |
| Tester Display |
|---|
| ACC SW |
| IG SW |
The GTS display changes correctly in response to the ignition switch state.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Remove the ignition or starter switch assembly.
Click hereEngine / Hybrid System>2AR-FE (STARTING)>IGNITION SWITCH>REMOVAL
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>2AR-FE (STARTING)>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3F and 3E instrument panel junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3F-1 - Body ground | Always | 11 to 14 V |
| 3E-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-3 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3A instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K30-8 (IG1) - 3A-17 | Always | Below 1 Ω |
| K30-6 (ACC) - 3A-30 | Always | Below 1 Ω |
| K30-7 (AM1) - 3A-44 | Always | Below 1 Ω |
| K30-8 (IG1) or 3A-17 - Other terminals and body ground | Always | 10 kΩ or higher |
| K30-6 (ACC) or 3A-30 - Other terminals and body ground | Always | 10 kΩ or higher |
| K30-7 (AM1) or 3A-44 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the instrument panel junction block assembly with a new or known good one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the active arming mode function.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION
The active arming mode function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG