Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328239 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Unlock Warning Switch Circuit  


DESCRIPTION

The unlock warning switch assembly turns on when the key is inserted into the ignition key cylinder and turns off when the key is removed.

WIRING DIAGRAM

B472461E02
1.615,1.146 3.063,1.542 1.448,0.396 10 false Unlock Warning Switch Assembly 1.625,0.99 2.073,1.177 0.448,0.188 10 false K31 1.865,0.625 2.313,0.813 0.448,0.188 10 false 2 2.667,0.625 3.115,0.813 0.448,0.188 10 false 1 3.99,0.625 4.438,0.813 0.448,0.188 10 false 41 3.781,1.156 4.229,1.344 0.448,0.188 10 false 3A 3.781,1.313 5.375,1.677 1.594,0.365 10 false Instrument Panel Junction Block Assembly 5.302,0.625 5.75,0.813 0.448,0.188 10 false 3 5.479,0.719 6.104,0.896 0.625,0.177 10 false KSW 5.115,2.635 5.74,2.813 0.625,0.177 10 false MB 5.115,2.802 6.76,3.188 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

PROCEDURE

1.READ VALUE USING GTS (KEY UNLOCK WARNING SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch OFF or ON OFF: Ignition key not inserted
ON: Ignition key inserted
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

The GTS display changes correctly in response to the unlock warning switch assembly status.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B472424C02
3.271,0.188 3.792,0.479 0.521,0.292 3.344,1.563 3.865,1.854 0.521,0.292 1.552,2.646 1.333,2.646 1.333,2.646 1.333,2.313 false 3.438,0.24 3.75,0.438 0.313,0.198 10 false 3A 3.49,1.625 3.802,1.823 0.313,0.198 10 false MB 1.594,2.573 2.125,2.771 0.531,0.198 10 false KSW 0.208,0.146 0.521,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-41 - MB-3 (KSW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-41 - K31-1 Always Below 1 Ω
3A-41 or K31-1 - Other terminals and body ground Always 10 kΩ or higher
K31-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR