Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module)
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328248 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P261401  Camshaft Position Signal Output "A" General Electrical Failure  


DESCRIPTION

Refer to DTC P001001.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P001001

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P261401 Camshaft Position Signal Output "A" General Electrical Failure Malfunction in rotation sensor of cam timing control motor with EDU assembly is detected for 3 seconds (1 trip detection logic).
·

Cam timing control motor with EDU assembly

·

ECM


Comes on DTC stored SAE Code: P2614

Symptoms and Fail-safe Operation During Camshaft Control Motor Malfunction
Vehicle Condition Fail-Safe
·

Engine difficult to start

·

Lack of power


The cam timing control motor with EDU assembly is operated to the most retarded position.

MONITOR DESCRIPTION

This DTC is output when a malfunction in the cam timing control motor rotation sensor is detected. The cam timing control motor with EDU assembly is equipped with a self diagnostic function, which is used to output diagnosis signals (VTM) to the ECM. If the ECM receives a duty signal of 40%, this DTC is output immediately (1 trip detection logic).

MONITOR STRATEGY

Required sensor/Components Cam timing control motor with EDU assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more [A].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

10.

Read the DTCs.

HINT:
·

If a DTC is output, the system is malfunctioning.

·

If a DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P261401.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [B] again.




CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.REPLACE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY
a.

Replace the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>CAMSHAFT TIMING CONTROL MOTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the cam timing control motor with EDU assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTC P261401 is output B



A

END

B