Home › Engine / Hybrid System › A25A-FKS (EMISSION CONTROL) › CANISTER (w/ Canister Pump Module)
RM33A0E _51 Engine / Hybrid System _065344 A25A-FKS EMISSION CONTROL _0328569 CANISTER(w/ Canister Pump Module) A

A25A-FKS EMISSION CONTROL  CANISTER(w/ Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 77740R 1.INSTALL LEAK DETECTION PUMP SUB-ASSEMBLY

HINT:

Only perform this procedure when replacement of the leak detection pump sub-assembly is necessary.


a.
A401941

Engage the 2 claws to install a new leak detection pump sub-assembly to the No. 2 charcoal canister sub-assembly.

NOTICE:
·

Do not allow foreign matter such as grease, oil or water to adhere to the O-ring.

·

Ensure that the claws are engaged properly.




Hide 77730A 2.INSTALL NO. 2 CHARCOAL CANISTER SUB-ASSEMBLY

a.

Remove the rear suspension member sub-assembly.

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER>REMOVAL


b.

Install the No. 2 charcoal canister sub-assembly to the vehicle body with the 3 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Connect the leak detection pump sub-assembly connector.


d.

Push in the air line tube to the pipe (leak detection pump sub-assembly) until the air line tube makes a "click" sound.

NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the tube connector and pipe (leak detection pump sub-assembly) before performing this work.

·

After connecting the air line tube, check that the air line tube is securely connected by pulling on the tube connector.




e.

Install the rear suspension member sub-assembly.

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER>INSTALLATION


Hide 77740 3.INSTALL CANISTER (CHARCOAL CANISTER ASSEMBLY)

a.

Install the clip to the vehicle body.


b.
A401942

Engage the claw to install the canister (charcoal canister assembly) to the vehicle body as shown in the illustration.


c.

Engage the clip to the canister (charcoal canister assembly).


d.

Install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the purge line hose to the canister (charcoal canister assembly) and slide the clip to secure it.


f.
A401945C01
2.156,2.625 2.458,2.625 false 2.49,2.531 2.75,2.729 0.26,0.198 10 false *a
*a Retainer
V100135

Push in


Push the vent line hose onto the canister (charcoal canister assembly) and push in the retainer to engage the lock claws.

NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the tube connector and pipe (canister (charcoal canister assembly)) before performing this work.

·

After connecting the vent line hose, check that the vent line hose is securely connected by pulling on the tube connector.




g.
A401944C01
1.885,2.677 2.219,2.677 false 2.26,2.583 2.531,2.781 0.271,0.198 10 false *a
*a Retainer
V100135

Push in


Push the fuel tank vent hose onto the canister (charcoal canister assembly) and push in the retainer to engage the lock claws.

NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the tube connector and pipe (canister (charcoal canister assembly)) before performing this work.

·

After connecting the fuel tank vent hose, check that the fuel tank vent hose is securely connected by pulling on the tube connector.




Hide 48832A 4.INSTALL REAR NO. 1 STABILIZER BAR BRACKET

a.

Install the 2 rear No. 1 stabilizer bar brackets to the vehicle body with the 4 bolts.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 17420 5.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install 2 new gaskets to the front exhaust pipe assembly (TWC: Rear Catalyst) and center exhaust pipe assembly.


b.

Connect the center exhaust pipe assembly to the exhaust pipe support.


c.

Install the center exhaust pipe assembly to the front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly with 4 new bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)